[SI-LIST] Re: Split gnd planes - for/against?
- From: Duane Mattheisen <duane.mattheisen@xxxxxxx>
- To: Lee Ritchey <leeritchey@xxxxxxxxxxxxx>, Steve Weir <weirsi@xxxxxxxxxx>
- Date: Tue, 7 Apr 2009 22:45:01 +0200
I had a combiner limiter that had about 100dB of gain, it was used in a
satilite reciever. There were three aplifier stages to bring up the gain to
100dB. Oscilations would happen because the last output stage's current would
run through the ground plane and pass by the input of the first stage. The
oscilations were stoped by making a trench in the ground plane at the middle
stage of the amplifiers and moving the ground wire to the bottom of the trench.
Regards, Duane Mattheisen
-----Original Message-----
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On
Behalf Of Lee Ritchey
Sent: 2009 Apr 07 11:28 AM
To: Steve Weir
Cc: Charles Grasso; Sol Tatlow; si-list
Subject: [SI-LIST] Re: Split gnd planes - for/against?
Steve,
You have described a hypothetical case here. I'm looking for a real one.
You didn't reply with "you will have to get a case yourself" as some do.
Refusing to supply an example to support claims is tantamount to making
things up.
If a claimer can't show a case where a rule works, the claim should not be
made.
Lee
> [Original Message]
> From: steve weir <weirsi@xxxxxxxxxx>
> To: <leeritchey@xxxxxxxxxxxxx>
> Cc: Charles Grasso <Charles.Grasso@xxxxxxxxxxxx>; Sol Tatlow
<Sol.Tatlow@xxxxxxxxxxxxxxxxxxxx>; si-list <si-list@xxxxxxxxxxxxx>
> Date: 4/7/2009 11:13:14 AM
> Subject: Re: [SI-LIST] Re: Split gnd planes - for/against?
>
> Lee and this will be true in the majority of cases, and almost without
> exception where a board is digital only. For an example of where a
> split works, and it must be done properly or all bets are off:
>
> Circuit region 1, noise sensitivity is in the uV's. Let's assume the
> power / ground separation is 4 mils. The spreading inductance is
> roughly 128pH / square. Now assume that there is an adjacent circuit
> region that has a 64 bit memory bus on it. Let's assume very pedestrian
> 200ps rise times on 18mA swing. That bus is switching just over
> 5E9A/s. If circuit region 1 has a noise limit of 10uV across its length
> and a square aspect ratio, then we need over 90dB isolation. We aren't
> going to get there with placement and bypass caps alone. But we can get
> there by including well designed moating
>
> You are absolutely correct that many people put moats in they don't need
> and worse do so in a way that creates other more serious problems.
> Moats are sort of like ferrite beads: they are tools that have
> particular value is specific circumstances. They always come with a
> price. Their must be justified as needed and appropriate, and once used
> engineered correctly.
>
> Best Regards,
>
>
> Steve.
> Lee Ritchey wrote:
> > I've taught my high speed class to more than 7000 engineers and
designers
> > over the years. In each class, I ask for examples where splitting a
ground
> > plane actually made a circuit work better with the promise to add the
> > example to my class.
> >
> > To date, there have been no examples provided. There has been a bit of
> > hand waving on the topic but no clear examples that can be defended.
The
> > usual reason is "we've done it this way for years and it has worked."
To
> > me, that sounds an awful lot like the man who jumped off the 20 story
> > building and reported as he passed the 10th floor, "so far, so good".
> > Splitting the ground plane just hasn't shown up as a problem, not that
is
> > actually fixed anything.
> >
> > I have fixed EMI problems several times by removing splits in ground
> > planes. Some of see this as easy money!
> >
> > I'll make the same offer to this group. Show me an example where
splitting
> > ground planes helps and I'll make it a part of my course.
> >
> > Lee Ritchey
> >
> >
> >
> >> [Original Message]
> >> From: Grasso, Charles <Charles.Grasso@xxxxxxxxxxxx>
> >> To: steve weir <weirsi@xxxxxxxxxx>; Sol Tatlow
> >>
> > <Sol.Tatlow@xxxxxxxxxxxxxxxxxxxx>
> >
> >> Cc: si-list <si-list@xxxxxxxxxxxxx>
> >> Date: 4/7/2009 9:57:52 AM
> >> Subject: [SI-LIST] Re: Split gnd planes - for/against?
> >>
> >> We use split planes all the time.
> >> When you have circuits of *vastl8 different noise floors co-existing
> >> on one board - it's the only way to go.
> >>
> >> Chas
> >>
> >> -----Original Message-----
> >> From: si-list-bounce@xxxxxxxxxxxxx
[mailto:si-list-bounce@xxxxxxxxxxxxx]
> >> On Behalf Of steve weir
> >> Sent: Tuesday, April 07, 2009 10:11 AM
> >> To: Sol Tatlow
> >> Cc: si-list
> >> Subject: [SI-LIST] Re: Split gnd planes - for/against?
> >>
> >> Sol, unfortunately there is not a single answer. In most cases
moating
> >> is a bad idea, particularly if one does not understand the caveats and
> >> how to deal with them. It's not just the moats: It's the placement,
> >> clearances, stitching, and routing that all need to be considered.
> >>
> >> Steve
> >>
> >> Sol Tatlow wrote:
> >>
> >>> I know this subject has been raised before, countless times in one
> >>> guise or another. I have also googled plenty. I'm not looking for
> >>> theoretical opinions, either, about whether or not, or when, they
> >>> should be used (specifically not, "it depends", unless you've got
> >>> REAL-LIFE examples, for and against!!!).
> >>>
> >>> This subject raised its head for me in this case due to using
> >>> 2 A/Ds as well as 2 D/As, both from Analog Devices, where one
> >>> specifies a split plane, the other specifies no split. Now, I am
> >>> all too wary of relying simply on evaluation boards, where, in
> >>> general, one layout is done, and if it works, that's how everyone
> >>> should do it (_without_ comparing 2 different approaches).
> >>>
> >>> I personally have 3 concrete cases where split gnds had no positive
> >>> effect on SI, but significantly worsened EMC results (despite
> >>> sticking to all the usual guidelines, like no tracks over the
> >>> splits, etc.), but I have no concrete case FOR split ground planes.
> >>>
> >>> So, what I'm interested in is: does anyone have CONCRETE examples
> >>> which they would like to share for/against split planes? The kind
> >>> of thing I mean would be like in one of the cases I had, where I
> >>> wanted to go against the suggested approach of using a split gnd,
> >>> and persuaded my customer to pay for 2 variants of the same board
> >>> on the same manufacturing panel, one with split ground, one with
> >>> solid ground. Both variants were assembled and tested, with regards
> >>> to both SI as well as EMC: both were functionally satisfactory; at
> >>> EMC testing, however, the split-plane bombed out big time, while
> >>> the non-split sailed through. I like to think that it wasn't due
> >>> to any screw-ups on my side, that the split ground failed - I am
> >>> not a newbie to PCB layouts, and, while for sure no professional
> >>> expert on all areas of SI, I believe I avoided the typical blunders
> >>> often present in split ground layouts.
> >>>
> >>> Anyway, my customer was more than happy, but not everyone has the
> >>> money/time/desire to do as I suggested. So, any 'war stories' to
> >>> support one or the other approach would be appreciated to help
> >>> expand my knowledge and understanding of this subject - obviously,
> >>> we all respect confidentiality, so I'm not looking for circuits,
> >>> layouts and so on, but I figure many of you must have stories that
> >>> can be related regarding this subject. Or perhaps some good links
> >>> to non-confidential 'real-life' examples/studies?
> >>>
> >>> Regards,
> >>> Sol
> >>>
> >>>
> >>>
> >> --
> >> Steve Weir
> >> Teraspeed Consulting Group LLC
> >> 121 North River Drive
> >> Narragansett, RI 02882
> >>
> >> California office
> >> (866) 675-4630 Business
> >> (707) 780-1951 Fax
> >>
> >> Main office
> >> (401) 284-1827 Business
> >> (401) 284-1840 Fax
> >>
> >> Oregon office
> >> (503) 430-1065 Business
> >> (503) 430-1285 Fax
> >>
> >> http://www.teraspeed.com
> >> This e-mail contains proprietary and confidential intellectual property
> >> of Teraspeed Consulting Group LLC
> >>
------------------------------------------------------------------------
> >> ------------------------------
> >> Teraspeed(R) is the registered service mark of Teraspeed Consulting
> >> Group LLC
> >>
> >> ------------------------------------------------------------------
> >> To unsubscribe from si-list:
> >> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
> >>
> >> or to administer your membership from a web page, go to:
> >> //www.freelists.org/webpage/si-list
> >>
> >> For help:
> >> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
> >>
> >>
> >> List technical documents are available at:
> >> http://www.si-list.net
> >>
> >> List archives are viewable at:
> >> //www.freelists.org/archives/si-list
> >> or at our remote archives:
> >> http://groups.yahoo.com/group/si-list/messages
> >> Old (prior to June 6, 2001) list archives are viewable at:
> >> http://www.qsl.net/wb6tpu
> >>
> >>
> >> ------------------------------------------------------------------
> >> To unsubscribe from si-list:
> >> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
> >>
> >> or to administer your membership from a web page, go to:
> >> //www.freelists.org/webpage/si-list
> >>
> >> For help:
> >> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
> >>
> >>
> >> List technical documents are available at:
> >> http://www.si-list.net
> >>
> >> List archives are viewable at:
> >> //www.freelists.org/archives/si-list
> >> or at our remote archives:
> >> http://groups.yahoo.com/group/si-list/messages
> >> Old (prior to June 6, 2001) list archives are viewable at:
> >> http://www.qsl.net/wb6tpu
> >>
> >>
> >
> >
> >
> >
>
>
> --
> Steve Weir
> Teraspeed Consulting Group LLC
> 121 North River Drive
> Narragansett, RI 02882
>
> California office
> (866) 675-4630 Business
> (707) 780-1951 Fax
>
> Main office
> (401) 284-1827 Business
> (401) 284-1840 Fax
>
> Oregon office
> (503) 430-1065 Business
> (503) 430-1285 Fax
>
> http://www.teraspeed.com
> This e-mail contains proprietary and confidential intellectual property
of Teraspeed Consulting Group LLC
>
----------------------------------------------------------------------------
--------------------------
> Teraspeed(R) is the registered service mark of Teraspeed Consulting Group
LLC
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.net
List archives are viewable at:
//www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.net
List archives are viewable at:
//www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
Other related posts:
