[SI-LIST] Re: Solving signal integrity problems at very high data rates - EDN

  • From: Chuck Corley <corley@xxxxxxxxx>
  • To: telegrapher9@xxxxxxxxx
  • Date: Thu, 22 Dec 2016 14:55:13 -0800

It appears to be an Intel patent application, so knowing them as a
fairly honest company hopefully they wouldn't show it in publications
without disclosing they have a patent on it, or allowing free use of it
??   
Yes, I know that other companies have actually done this in the past
(added patented technologies to standards and later try to sue everyone
who built using standard, etc.), but I'm hoping Intel isn't like that. 

Chuck Corley

On 2016-10-18 13:58, Dave Cuthbert wrote:

Is this what is shown in US patent 7,501,586?
Dave CuthbertOn Oct 18, 2016 14:46, "Bayer, David (US COM)" 
<David.Bayer@xxxxxxxxxx> wrote: 

Could you elaborate on what a boomerang via is / how it is constructed? 

Thanks 
David 

-- 
David Bayer 

-----Original Message----- 
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Lee Ritchey 
Sent: Wednesday, October 12, 2016 11:37 AM 
To: antokdavis@xxxxxxxxx; si-list@xxxxxxxxxxxxx 
Subject: [SI-LIST] Re: Solving signal integrity problems at very high data 
rates - EDN 

If you attended the PCIe Gen 3 boot camp at DesignCon 2016 put on by Intel, 
you would find that they recommend a thing called a boomerang via to get 
from a trace on the top of a PCB to a  through hole connector pin without 
the need to remove the via stub.  This is an example of distributing the 
parasitic capacitance of the via barrel along its length, which is an 
inductor, to minimize its effect on the signal.  

IF you think about it, what is being done is using the via as a transmission 
line just like the traces. 

When the dimensions of the vias under a  1 mm pitch BGA are done to account 
for manufacturability issues, the vias, when traveled length wise, will be 
slightly higher in impedance that 50 ohms.  This is fine as the reflection 
from this, which will be quite small, is overshoot which does not erode the 
signal noise margin. 

Same thing happens when a large router is designed with a mid plane that has 
the switch cards on one side and the line cards on the other at right angles 
with all of the fast signals only in the plug in cards and none on the 
backplane itself.  All of the fast signals travel the length of the plated 
through holes in the backplane. 

Only on the plug in cards is it necessary to employ back drilling or 
boomerang vias. 

Hope this clears this up a bit. 

All of the above statements have been verified with many lab measurements. 
Probably doesn't surprise those of you who know me.  

Lee 

-----Original Message----- 
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Anto Kavungal Davis 
Sent: Wednesday, October 12, 2016 5:47 AM 
To: si-list@xxxxxxxxxxxxx 
Subject: [SI-LIST] Solving signal integrity problems at very high data rates 
- EDN 

Hi, 
I was going through Solving signal integrity problems at very high data 
rates - EDN, by Lee Ritchey, Scott McMorrow & Kella Knack -October 04, 2016 
Any papers/publications based on the following comment or with similar 
results. 

"What has been demonstrated by simulations as well as by laboratory 
measurement is that when a signal travels the length of the plated through 
hole or via, the parasitic capacitance of the hole is distributed along the 
length of the hole, rendering it virtually invisible." 

Thanks, 
Anto 

------------------------------------------------------------------ 
To unsubscribe from si-list: 
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field 

or to administer your membership from a web page, go to: 
//www.freelists.org/webpage/si-list ;

For help: 
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field 

List forum  is accessible at: 
http://tech.groups.yahoo.com/group/si-list ;

List archives are viewable at:     
//www.freelists.org/archives/si-list ;

Old (prior to June 6, 2001) list archives are viewable at: 
http://www.qsl.net/wb6tpu ;

------------------------------------------------------------------ 
To unsubscribe from si-list: 
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field 

or to administer your membership from a web page, go to: 
//www.freelists.org/webpage/si-list ;

For help: 
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field 

List forum  is accessible at: 
http://tech.groups.yahoo.com/group/si-list ;

List archives are viewable at:     
//www.freelists.org/archives/si-list ;

Old (prior to June 6, 2001) list archives are viewable at: 
http://www.qsl.net/wb6tpu ;

------------------------------------------------------------------ 
To unsubscribe from si-list: 
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field 

or to administer your membership from a web page, go to: 
//www.freelists.org/webpage/si-list ;

For help: 
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field 

List forum  is accessible at: 
http://tech.groups.yahoo.com/group/si-list ;

List archives are viewable at:     
//www.freelists.org/archives/si-list ;

Old (prior to June 6, 2001) list archives are viewable at: 
http://www.qsl.net/wb6tpu
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field

List forum  is accessible at:
http://tech.groups.yahoo.com/group/si-list

List archives are viewable at:     
//www.freelists.org/archives/si-list

Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu

------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field


List forum  is accessible at:
               http://tech.groups.yahoo.com/group/si-list

List archives are viewable at:     
                //www.freelists.org/archives/si-list
 
Old (prior to June 6, 2001) list archives are viewable at:
                http://www.qsl.net/wb6tpu
  

Other related posts: