[SI-LIST] Re: Input Matching for SMA Connectors

  • From: Jonathan Riley <jonathan.lloyd.riley@xxxxxxxxx>
  • To: hakim.sellaoui@xxxxxxxxxxxxxxx
  • Date: Tue, 11 Oct 2016 20:04:52 +0100

Hi Hakim
Good advice from the other contributors. If you can't find any recommended
launch pattern data, and haven't got access to a decent simulator, there
are still some remarks that are worth making (but they are generalisations
- and should be treated as such):

1. Putting a plane cut-out in the reference plane just under the centre
pin. The size of the cut-out should be as big as you can make it without
letting it affect the four Shield pins on the SMA body. This has the effect
of keeping the 50 Ohms impedance about right as you transition from PCB to
SMA.

2. If you can, use an SMA connector where the centre pin is surface mount
style (doesn't matter about the four shield pins). This is because a PCB
trace on the top side of the board does not need any via, and the presence
of one caused by being the centre pin gives you two problems. (a) It lowers
the impedance at the point where the incoming signal sees both the top
layer trace and also the connection through the board. And (b) the stub
that is the connector pin passing through the PCB and out on the other side
will cause reflections which at certain frequencies will given you a lot of
signal cancellation, this is seen on the S21 plot as big dips appearing at
multiples of the first notch frequency. I'd bet that the first one of the
notches will be low enough to be within your 5 GHz band, and so should not
be neglected.

Regards
Jon

On 11 October 2016 at 17:40, Tom Dagostino <tom@xxxxxxxxxxxxxxxxx> wrote:

Hakim

Many connector manufacturers publish recommended launches for their
connectors. You might want to check with your vendor...

Tom Dagostino
971-279-5325
tom@xxxxxxxxxxxxxxxxx

Teraspeed Labs
9999 SW Wilshire Street
Suite 102
Portland, OR 97225


-----Original Message-----
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx]
On
Behalf Of Hakim Sellaoui
Sent: Tuesday, October 11, 2016 4:25 AM
To: si-list@xxxxxxxxxxxxx
Subject: [SI-LIST] Input Matching for SMA Connectors

Hi all,
I'm designing a test board that will have differential trace widths of 4
mil
and I want to connect SMA connectors to them, but I'm not sure what
connector would be suitable as the ones I've found have connector widths
that are neither equal to or smaller than the trace widths, as well as the
recommended pad sizes are much larger.  For an RF design I did at Uni, I
just added a quarter wave transformer to provide the matching at the
operating frequency; is it still possible to do this with a high-speed
design with a 200 ps rise time (5 GHz) signal?

Or can anyone recommended a way to connect VNA coaxial cables to a PCB with
trace widths around 4 mils, such that the Zo is maintained.

Thanks,

--
Hakim Sellaoui
Associate Hardware Engineer
DisplayLink (UK) Limited

Tel: +44 (0)1223 443920
Fax: +44 (0)1223 443921
E: hakim.sellaoui@xxxxxxxxxxxxxxx<mailto:hakim.sellaoui@xxxxxxxxxxxxxxx>
W: http://www.displaylink.com/

140 Science Park, Milton Road,
Cambridge, CB4 0GF,
United Kingdom.
Registered in England No. 04811048

DisplayLink Corp.
A US incorporated company.
480 S. California Avenue Ste 305, Palo Alto, CA 94306, USA.


------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field


List forum  is accessible at:
               http://tech.groups.yahoo.com/group/si-list

List archives are viewable at:
                //www.freelists.org/archives/si-list

Old (prior to June 6, 2001) list archives are viewable at:
                http://www.qsl.net/wb6tpu


------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field


List forum  is accessible at:
               http://tech.groups.yahoo.com/group/si-list

List archives are viewable at:
                //www.freelists.org/archives/si-list

Old (prior to June 6, 2001) list archives are viewable at:
                http://www.qsl.net/wb6tpu





------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field


List forum  is accessible at:
               http://tech.groups.yahoo.com/group/si-list

List archives are viewable at:     
                //www.freelists.org/archives/si-list
 
Old (prior to June 6, 2001) list archives are viewable at:
                http://www.qsl.net/wb6tpu
  

Other related posts: