[SI-LIST] Re: Hot-swap issue on HDMI Bus
- From: "Kenneth W. Egan" <kegan@xxxxxxxxxxxxx>
- To: "'Sriram Subburathinam, ERS-HCLTech'" <sriramsr@xxxxxxx>, <si-list@xxxxxxxxxxxxx>
- Date: Sun, 19 Dec 2010 09:37:32 -0600
Uh. Might want to think of Ldi/dt before you start that.
if you're driving more than a ft of cable, that's one hell of an inductance.
Kenneth W. Egan
This Email is covered by the Electronic Communications Privacy Act: 18 USC
secs. 2510-2521
The information contained in this electronic mail message is privileged,
confidential or otherwise legally exempt from disclosure, in addition may be
subject to the attorney-client privilege and is intended solely for the use
of the addressee. If you are not the intended recipient, any disclosure,
copying, distribution, or the taking of any action in reliance on the
contents of this message is strictly prohibited. If you have received this
message in error, please notify me immediately and delete all copies of the
message.
-----Original Message-----
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On
Behalf Of Sriram Subburathinam, ERS-HCLTech
Sent: Sunday, December 19, 2010 1:51 AM
To: si-list@xxxxxxxxxxxxx
Subject: [SI-LIST] Hot-swap issue on HDMI Bus
Hi Experts,
Have you come across any hot-plug solution for HDMI bus, similar to IDT
Quickswitch products? In our system ( HDMI Sink) , there is a back drive
from the HDMI lines to the HDMI receiver power supply rails prior to the
power supply ramp-up. I am looking for a solution where in the HDMI data
lines could be isolated by a GPIO control and that solution should not have
any ESD clamp to power rails to avoid back drive. Any suggestions?
Please note: 1. This is a custom cabling / interface where in the HDMI data
+ power is fed from the source, 2. There is no control over the Source /
Cabling.
Thanks and regards,
Sriram SR
::DISCLAIMER::
----------------------------------------------------------------------------
-------------------------------------------
The contents of this e-mail and any attachment(s) are confidential and
intended for the named recipient(s) only.
It shall not attach any liability on the originator or HCL or its
affiliates. Any views or opinions presented in
this email are solely those of the author and may not necessarily reflect
the opinions of HCL or its affiliates.
Any form of reproduction, dissemination, copying, disclosure, modification,
distribution and / or publication of
this message without the prior written consent of the author of this e-mail
is strictly prohibited. If you have
received this email in error please delete it and notify the sender
immediately. Before opening any mail and
attachments please check them for viruses and defect.
----------------------------------------------------------------------------
-------------------------------------------
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.net
List archives are viewable at:
//www.freelists.org/archives/si-list
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.net
List archives are viewable at:
//www.freelists.org/archives/si-list
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
Other related posts:
