[rc3r] Re: Happy 4th

  • From: Charles Kehoe <charlesjkehoe@xxxxxxx>
  • To: "rc3r@xxxxxxxxxxxxx" <rc3r@xxxxxxxxxxxxx>
  • Date: Sat, 4 Jul 2020 00:22:14 +0000

[Animated GIF]

If it makes this much noise, add me to that list, I'll be right over.

Charles J. Kehoe, ACSW, CCE
Chief Operating Officer
Kehoe Correctional Consulting, LLC
P.O. Box 1265
Midlothian, VA 23113
(804) 873-4949
Web site: www.charlesjkehoe.com<http://www.charlesjkehoe.com>



________________________________
From: rc3r-bounce@xxxxxxxxxxxxx <rc3r-bounce@xxxxxxxxxxxxx> on behalf of Thomas 
Gilsdorf <dmarc-noreply@xxxxxxxxxxxxx>
Sent: Friday, July 3, 2020 7:15 PM
To: dmarc-noreply@xxxxxxxxxxxxx <dmarc-noreply@xxxxxxxxxxxxx>; 
rc3r@xxxxxxxxxxxxx <rc3r@xxxxxxxxxxxxx>
Subject: [rc3r] Re: Happy 4th

Train stuff. The Chicane is rebuilt on the 12x15, wired, tested, and ready for 
ballast. The circuit breakers are installed and tested on the 12x15. Minutes 
from the RF&P will be out to you guys in a little while.

Boat stuff: We're not on the Potomac headed to DC on the boat for the 
fireworks. However, I have fired the engine for the first time in three years, 
disposed of 35 gallons of bad gas. Most of the maintenance work is done. Down 
to a very short list of work left. We will be on the water in July.

Today, we put electrical power on my younger son's 1960 Dodge in the garage. We:

Isolated a short on the horn circuit, we'll deal with that later. This was a 
real honest to goodness fuse blowing nothing else is going to work until we fix 
this dang short, short.
Rewired (correctly) the electrical emergency shut-off switch
Checked / reset rocker arm clearance on the valves
Spun the engine over and primed it with oil (75 psi cold, that's a LOT). The 
oil pump was packed with Vasoline and sucked up the prime like a champ. The 
dang drain plug (of all things) is leaking, NUTZ
Set the initial static timing on the distributor. Installed the spark plugs and 
wires.
Rewired the entire ignition circuit. Thankfully his wiring boo-boos didn't fry 
anything. We did heat up the coil pretty good and swapped it out for good 
measure.FWIW, he was trying to wire with pieces of three diagrams, from three 
different manufacturers. There was no complete schematic for what is installed 
on the car. We now have ignition! The MSD (multiple spark discharge) controller 
throws a spark like a flame thrower. We could probably set pancake syrup on 
fire with these spark plugs.
Fuel pump runs, we haven't put any fuel in the fuel cell, yet. That system 
still needs to be leak checked.
Checked-out the electric cooling fan. Works
Totally unplanned, but FWIW, the windshield wipers are working. Albeit the 
switch is wired backwards.
Built two temporary exhaust dump pipes off of the exhaust header

I know much of this will leave most of you guys cold. We accomplished more 
today than we have all year. There is a short list before we try to fire this 
engine. Tommy reminded me that I assembled it for him 17 years ago. It is still 
super clean and spins over freely. I'm 99% confident that once we add fuel to 
the equation, it is going to be making noise. A LOT of noise. Bob Buehler and 
(both) Peters, if you're outside when we do this you will probably hear us.

Gilly

-----Original Message-----
From: John Crockett <dmarc-noreply@xxxxxxxxxxxxx>
To: rc3r@xxxxxxxxxxxxx <rc3r@xxxxxxxxxxxxx>
Sent: Fri, Jul 3, 2020 1:16 pm
Subject: [rc3r] Happy 4th

Hope everyone has a great and safe Independence Day celebration.

John

Other related posts: