[pure-silver] Re: enlarger meter

  • From: Shannon Stoney <shannonstoney@xxxxxxxxxxxxxxx>
  • To: pure-silver@xxxxxxxxxxxxx
  • Date: Fri, 9 Nov 2007 14:47:26 -0600

Here is what is says at the BH site about the Ilford enlarging meter. It sounds very complicated! I trust it's not as hard to use as it sounds?


--shannon

The Ilford EM10 Exposure Monitor is a simple to use enlarging exposure meter for both black & white and color printing.

The recommended procedure to use the Ilford EM10 Exposure Monitor is to first make an acceptable, full frame print to serve as a standard and record all pertinent exposure and printing data.

You will need the enlarger height, exposure time and aperture, but record other data such as the filter used, exposure time and developing conditions.

Use the same printing time and printing conditions when making a print from the new negative. It is preferred to measure the standard negative and the new negative to be printed with no variable contrast filter in the enlarger filter holder or drawer and record in your notes the calibration and new negative when measured without the filter.

You can calibrate with or without the filter in place, just be consistent when you make the measurements.

To calibrate the meter using the standard test negative in the enlarger, set at the aperture and enlarger height that was used to make the acceptable print.

* For negatives measure the shadow area that is brightest, but with detail, in the projected image with EM10 resting on the baseboard of the enlarger.

* For slides (Ilforchrom printing) measure a white area with detail. You cannot measure a black or white area with any exposure meter to calibrate the meter or measure a new negative for exposure. Rotate the dial until the green light is lit. The meter is calibrated.

Record the dial position in case the dial is accidentally moved. Insert the negative to be printed in the enlarger and focus. Place the meter in the brightest shadow area with detail.

For a slide find a white area with detail to measure. Adjust the enlarger lens aperture until the green light is lit. The aperture is now set to print the negative using the same exposure time and filter as used to make the standard negative or slide.

Note: that the measurements with the EM must be made with no lights on except the enlarger (no safe light can be on). If you wish to crop the negative to be printed, first measure the print as described above as a full frame negative and then crop and re-measure to make the uncropped print.

The red light signifies the light level is too low. If you are unable to adjust the aperture and get the green light lit, then go to the standard setting and open the aperture by one stop and recalibrate the meter at this opening. Repeat the procedure, if needed, until the green light will lite when measuring the new negative.

Keep your standard negative and a print in a safe place to use when needed. Again, measure with no safe light on.


On Nov 9, 2007, at 9:59 AM, Chris Ellinger wrote:

Sauerwald Mark wrote:
I mistyped when I said 'Epson' - it is the Ilford
enlarging meter that I use. It has a sensor, a knob
and three LEDs, a red 'over' led, a red 'under' led
and a green just right.
I pick a neutral part of the image - usually a face if
it is a portrait, put the meter on the easel and turn
the knob until I get the green LED.  Raise the head,
then open the aperture until the Green LED comes back.

I use the same meter, and a slightly different procedure.

The meter has two controls: sensitivity and time. To compensate for change in magnification, I set the TIME control to the initial time, meter an area that has a uniform tone, and adjust the SENSITIVITY control for the green led. Then, change the magnification, meter the same area and find the new exposure time by adjusting the TIME control for the green led. This method compensates for changes in magnification and/or aperture.

(I've glued a small knob on the sensitivity control to make it easier to adjust.)

Chris Ellinger
Ann Arbor, MI
USA

http://www.ellingerphoto.com/
======================================================================= ====================================== To unsubscribe from this list, go to www.freelists.org and logon to your account (the same e-mail address and password you set-up when you subscribed,) and unsubscribe from there.


=============================================================================================================
To unsubscribe from this list, go to www.freelists.org and logon to your 
account (the same e-mail address and password you set-up when you subscribed,) 
and unsubscribe from there.

Other related posts: