Hi, I see that the reason for all this confusion is the internationalize wizard that has gone way too far. It has internationalized all strings, including all keywords. I will go through the entire configuration dialogue and remove every instance of it. 73 de Per, sm0rwo tis 2011-04-19 klockan 21:51 +0100 skrev G6CKR: > That worked as well. > Am I correct in thinking that the Offset seconds are being ignored in > this version? > Roger > On 19/04/11 20:56, G6CKR wrote: > > That worked. I have clicked it down to 2 for a 21:17 BST beacon. > > I have a Hospital trip for a routine Electrocardiogram in the morning so > > beacon will be off. I will install the latest version on the TX machine > > when I get back home. > > So look for beacons on minute 1 or 2 of the block depending on how I feel. > > 73 Roger > > On 19/04/11 20:34, G6CKR wrote: > >> I used the VNC via the LAN and have installed the new version, it has > >> read in 4 to the spinner window and I have not touched it.The audio goes > >> to the speakers so I will hear it hopefully at 20:49 BST and not before. > >> On 19/04/11 20:02, Rein Couperus wrote: > >>> I have changed the code in such a way that the beacon minute is now > >>> taken directly off the spinner... > >>> So WhatYouSeeIsWhatYouGet... whatever is in the config file. > >>> Tested here with 10, 30 and 60 minute periods... version 0.9.4-1 > >>> > >>> Rein PA0R > >>> > >>>> VNC access should be working with the same details if you want to remote > >>>> test. > >>>> Not tested via the Mi-Fi Second internet route but the settings on the > >>>> new router look right. > >>>> Otherwise I await your findigs > >>>> Roger > >>>> On 19/04/11 19:14, Rein Couperus wrote: > >>>>> I think I found it, testing.... > >>>>> > >>>>> Rein > >>>>> > >>>>>> On 19/04/11 12:08, G6CKR wrote: > >>>>>>> On 19/04/11 10:04, G6CKR wrote: > >>>>>>>> On 18/04/11 21:12, G6CKR wrote: > >>>>>>>>> perfs say minute 2 window says minute 2. > >>>>>>>>> Since 18:15 it has reverted to minute 0. > >>>>>>>>> > >>>>>>>>> http://aprs.fi/?c=raw&call=G6CKR&limit=50&view=normal > >>>>>>>>> has the evidence. > >>>>>>>>> 73 Roger > >>>>>>>>> > >>>>>>>> Restarted Jpskmail and touched nothing the first beacon went on > >>>>>>>> minute 0 > >>>>>>>> despite showing 2 in the window. I clicked up to 3 and back down to 2 > >>>>>>>> and it went again on the 2 (08:17:28 UTC on the raw data) I will > >>>>>>>> leave > >>>>>>>> it alone to see if it reverts back to 0 by it's self. > >>>>>>>> 73 Roger > >>>>>>>> > >>>>>>> I see from raw packets that my client has reverted the minute 0 again. > >>>>>>> I have not been back into the shack. > >>>>>>> Is it refreshing something and reading the default instead of the > >>>>>>> config > >>>>>>> file ?. > >>>>>>> Rein I have the dynamic address updating for the domain now so a look > >>>>>>> see is possible again. But I will update the second machine later > >>>>>>> today > >>>>>>> and see if it behaves the same way first. > >>>>>>> 73 Roger > >>>>>>> > >>>>>>> > >>>>>> removed jpskmail and .pskmail folders from second machine. > >>>>>> Used the installer for 9.0.3 but before first run replaced the.jar with > >>>>>> 9.0.4 version. > >>>>>> filled in basic details and set bcn minute to 2. > >>>>>> first beacon correct now reverted to 0 on this machine. > >>>>>> I'm stumped. > >>>>>> 73 Roger G6CKR > >>>>>> > >>>>>> > >>>>> > >>>> > >>>> > >>> > >> > >> > > > > > >