[modeleng] Re: Shaft pulley retaining

  • From: "Clifton" <clif.gwr@xxxxxxxxxxxx>
  • To: <modeleng@xxxxxxxxxxxxx>
  • Date: Wed, 18 Apr 2012 16:31:37 +0100

Hi Chris,

Having checked in my workshop Locktite 603 is the stuff.

Clif
----- Original Message ----- 
From: "Chris Crosskey" <chris.crosskey@xxxxxxxxx>
To: <modeleng@xxxxxxxxxxxxx>
Sent: Wednesday, April 18, 2012 1:29 PM
Subject: [modeleng] Re: Shaft pulley retaining


>I can easily get 601, 603, 638, 641, 648 and 660.....
> Chrisc
>
>
>
>> -----Original Message-----
>> From: modeleng-bounce@xxxxxxxxxxxxx [mailto:modeleng-
>> bounce@xxxxxxxxxxxxx] On Behalf Of Clifton
>> Sent: 18 April 2012 12:06
>> To: modeleng@xxxxxxxxxxxxx
>> Subject: [modeleng] Re: Shaft pulley retaining
>>
>> Hi Chris
>>
>> Locktite 601 I think is the stuff but will double check when I get into
>> workshop.
>>
>> Clean the shaft & pulley with Thinners. Slide the pulley onto shaft
>> just clear of it position, then run a bit of Loctite onto the shaft,
>> slide pulley into position & rotate slightly to spread locktite.
>>
>> Hold for about 1 min, set in 3 hours, fully hardened in 24 hours. After
>> which you will need a blowlamp to get it off.
>>
>> Will double check the Loctite number later.
>>
>> Clif
>> ----- Original Message -----
>> From: "Chris Crosskey" <chris.crosskey@xxxxxxxxx>
>> To: <modeleng@xxxxxxxxxxxxx>
>> Sent: Wednesday, April 18, 2012 9:11 AM
>> Subject: [modeleng] Shaft pulley retaining
>>
>>
>> > Does anyone have any recommendation for something that I can retain a
>> > pulley on a shaft... it's a sliding fit at the moment and I need it
>> to be
>> > able to act as a drive for a rotavator.... are any of the loctite
>> > compounds suitable for this? I'd rather avoid welding it on if at all
>> > possible.... currently my lathe is out of action during its move from
>> old
>> > workshop to the new one otherwise I'd bore out the pulley and weld it
>> to a
>> > sleeve that I could shrink fit ontop the shaft... It'd be a bugger to
>> key
>> > the shaft BTW, it's close to the cases of the Honda engine it's part
>> of
>> > and I don't want to strip the motor ....
>> > chrisc
>> >
>> >
>> _______________________________________________________________________
>> _
>> > This e-mail, and any attachment, is confidential. If you have
>> received it
>> > in error, do not use or disclose the information in any way, notify
>> me
>> > immediately, and please delete it from your system.
>> >
>> _______________________________________________________________________
>> _
>> > MODEL ENGINEERING DISCUSSION LIST.
>> >
>> > To UNSUBSCRIBE from this list, send a blank email to,
>> > modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
>> subject
>> > line.
>> >
>>
>> MODEL ENGINEERING DISCUSSION LIST.
>>
>> To UNSUBSCRIBE from this list, send a blank email to,
>> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
>> subject line.
>
> ________________________________________________________________________
> This e-mail, and any attachment, is confidential. If you have received it 
> in error, do not use or disclose the information in any way, notify me 
> immediately, and please delete it from your system.
> ________________________________________________________________________
> MODEL ENGINEERING DISCUSSION LIST.
>
> To UNSUBSCRIBE from this list, send a blank email to,
> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject 
> line.
> 

MODEL ENGINEERING DISCUSSION LIST.

To UNSUBSCRIBE from this list, send a blank email to, 
modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.

Other related posts: