I should have been more specific, if it's a DWL-122 and they say Tivo compatible, then I'm pretty sure it is kasmac compatible.
I'm sure since I've gotten mine, Tivo has added to there compatibility list and new devices that aren't prism2 might work, so... don't take my word for anything.
On 8/30/06, Rohan Hill <rohan@xxxxxxxxxxxxx> wrote: > Are you sure about that? Because most of these say Tivo compatible: > http://www.amazon.com/gp/offer-listing/B00005AW1H/ref=olp_tab_refurbished/10 > 3-5755914-4274200?ie=UTF8&condition=refurbished > > But they are WUSB11 version 2.8, which supposedly isn't a prism2 but rather > atmel chipset, and not supported by Kismac, according to this: > http://kismac.de/_trac/wiki/Hardware%20List > > > > > -----Original Message----- > From: kismac-bounce@xxxxxxxxxxxxx [mailto:kismac-bounce@xxxxxxxxxxxxx] On > Behalf Of John Warren > Sent: Wednesday, August 30, 2006 11:07 AM > To: kismac@xxxxxxxxxxxxx > Subject: [kismac] Re: Kismac captures 1,000,000+ packets, but none are DATA > or IVs ? > > there are a ton of prism2 usb's out there for far less than $100. Try ebay. > > Here's a link > http://cgi.ebay.com/D-Link-DWL-122-USB-Wireless-Adapter-TIVO-Series-2_W0QQit > emZ250022302659QQihZ015QQcategoryZ45002QQssPageNameZWDVWQQrdZ1QQcmdZViewItem > > If it says it's Tivo compatible than it's prism2. > > On 8/30/06, el_criuz <el.criuz@xxxxxxxxx> wrote: > > > > Something I discovered is that you will capture data packets and IVs when > > the network you try to crack is in use. If there is no traffic on the > > network you won't be able to capture data packets or just very few. > > I experienced the same problem, even with my Prism2 Chipset in use. > > On the other hand I managed to crack a frequently used network on a Zyxel > > Router within few days. For this I used both, my internal airport extreme > > card and the Prism2 USB Device. > > > > > > On 30.08.2006, at 07:34, Rohan Hill wrote: > > > > > > There's a driver with the latest build I have (158 I believe) that is > called > > Airport Extreme Passive Mode - or something to that effect. I had to > > completely trash my existing kismac, and install the latest build, and it > > took a couple tries, but the driver eventually showed up. I believe it's a > > standard option now though - and if you use the kismac installer, I don't > > know why you wouldn't see it. > > > > > > > > One word of advice - it's tedious to get any results with it - I've > captured > > over a million packets, and no IVs, and it doesn't seem to capture data > > packets AT ALL, even when there are plenty of data packets shooting > around. > > > > > > > > The problem, is that I can't seem to find ANY prism2 usb dongles available > > ANYWHERE for sale - at least under $100. > > > > > > ________________________________ > > > > > > From: kismac-bounce@xxxxxxxxxxxxx > > [mailto:kismac-bounce@xxxxxxxxxxxxx] On Behalf Of Michael > > Capizzo > > Sent: Tuesday, August 29, 2006 8:18 PM > > To: kismac@xxxxxxxxxxxxx > > Subject: [kismac] Re: Kismac captures 1,000,000+ packets, but none are > DATA > > or IVs ? > > > > > > > > Sorry for the misunderstanding but, how did you make the Airport Extreme > > card run under passive mode on the Macbook? If that option is in the 158 > > build, where can I find it? > > > > > > On Aug 29, 2006, at 7:52 PM, Court K wrote: > > > > > > > > > > > > You need to get a USB dongle that lets you do packet injects, and auth > > floods to get real IV packets. Passive mode on the airport cards is pretty > > much useless. > > > > > > > > > > > > > > > > On Aug 11, 2006, at 11:18 PM, Rohan Hill wrote: > > > > > > > > > > > > I'm running the latest (158 I believe?) build of Kismac, with a Macbook. > I'm > > using the Airport Extreme driver in passive mode to capture packets. > Here's > > the puzzling part - Kismac captures tons of packets, but when I look at > the > > details, NONE of these packets (I've let it run up over 1 million packets > in > > one case) are ever IVs or DATA. I can understand not coming up with any > IVs, > > but I don't see why I would never ever capture any data. At first I > thought > > this was just a fluke of my area, but I tried it today in the downtown of > a > > large city with 20+ access points in range, and still no Data or IVs. > > > > > > > > If I'm capturing from access points that are BEING USED at that moment, > how > > can there be no data? > > > > > > > > What's going on here - is this normal? > > > > > > > > > > > > > > > > > > > > > > > >