[jhb_airlines] Re: Torque Gauge Problem

  • From: Gerry Winskill <gwinsk@xxxxxxx>
  • To: jhb_airlines@xxxxxxxxxxxxx
  • Date: Sat, 23 Aug 2008 15:36:45 +0100

Refreshed by a walk amongst visiting bikes and bikers, I engaged remaining few grey cells and......did a Yahoo search.


The exact question had been asked on a sim-outhouse forum. The neccessary section of the line, which has my digital gauge working, in agreement with an existing analogue unit, is:

(A:TURB ENG MAX TORQUE PERCENT:1, percent)

So the full gauge .xml file now reads


<?xml version="1.0"?>
<Gauge Name="GW_WIND" Version="1.0">
<Image Name="GW_WIND.bmp"/>







        <Element>
        <Position X="45" Y="15"/>
<Text X="110" Y="80" Length="40" Font="quartz" Color="#FF0000" VerticalAdjust="Center">
           <String>%TORQUE %        %</String>
      </Text>
   </Element>

        <Element>
        <Position X="260" Y="15"/>
<Text X="110" Y="80" Length="40" Font="quartz" Color="#FFFF00" VerticalAdjust="Center"> <String>%((A:TURB ENG MAX TORQUE PERCENT:1,percent))%!03d! </String>
      </Text>
   </Element>







</Gauge>  



The forum is now in my Favourites

Gerry Winskill

Bones wrote:
I still think you have the comma in the wrong place - but your new line is
identical to the last you posted..
The string needs two values - the variable and the unit of measurement.
These should be separated by a comma.

Examples are:

((A:Turb eng2 N1, percent) abs)
(A:Eng1 manifold pressure, inHg)
(A:Prop1 RPM, rpm)

I don't have the list of A: variables here so I can only assume torque is
A:ENG1 TORQUE - in which case your line should read:

 ((A:ENG1 TORQUE, PERCENT) abs)


bones
bones@xxxxxxx
http://woodair.net


-----Original Message-----
From: jhb_airlines-bounce@xxxxxxxxxxxxx
[mailto:jhb_airlines-bounce@xxxxxxxxxxxxx] On Behalf Of Gerry Winskill
Sent: 22 August 2008 21:44
To: jhb_airlines@xxxxxxxxxxxxx
Subject: [jhb_airlines] Re: Torque Gauge Problem

Progress!

The line now reads <String>%((A:ENG1 TORQUE PERCENT,))%!03d! </String>

The gauge is now alive but the reading, with thrust lever at idle is  76169.

Next idea please...

Gerry Winskill

Bones wrote:
<String>%((A:ENG1 TORQUE PERCENT,))%!03d! </String>
<String>%((A:ENG1 TORQUE PERCENT,))%!03d! </String>
Should there be a comma between TORQUE and PERCENT? It's normally A VAR,
UNIT for this line so I presume you are asking for torque to be displayed
as
percent rather than a linear value.

bones
bones@xxxxxxx
http://woodair.net


-----Original Message-----
From: jhb_airlines-bounce@xxxxxxxxxxxxx
[mailto:jhb_airlines-bounce@xxxxxxxxxxxxx] On Behalf Of Gerry Winskill
Sent: 22 August 2008 16:43
To: jhb_airlines@xxxxxxxxxxxxx
Subject: [jhb_airlines] Torque Gauge Problem

In the Epic's Glass displays, there's no readout for the single engined turboprop's torque. Although the Prop RPM is displayed, it's too small to be legible.

So, I decided to make a new gauge for each, based upon one I made some time ago, for throttle position. The PROP RPM gauge is OK but the Torque gage displays but only as unchanging TORQUE 000

Below is the text content of the .xml gauge. Any ideas on how I need to change it will be overwhelmingly gratefully received!

Gerry Winskill





<?xml version="1.0"?>
<Gauge Name="GW_WIND" Version="1.0">
<Image Name="GW_WIND.bmp"/>







        <Element>
        <Position X="45" Y="15"/>
<Text X="110" Y="80" Length="40" Font="quartz" Color="#FF0000" VerticalAdjust="Center">
            <String>%TORQUE %        %</String>
       </Text>
    </Element>

        <Element>
        <Position X="260" Y="15"/>
<Text X="110" Y="80" Length="40" Font="quartz" Color="#FFFF00" VerticalAdjust="Center">
            <String>%((A:ENG1 TORQUE PERCENT,))%!03d! </String>
       </Text>
    </Element>







</Gauge>  







Other related posts: