Re: question on recording audio with Total Recorder
- From: Jean Menzies <jemenzies@xxxxxxx>
- To: jfw@xxxxxxxxxxxxx
- Date: Wed, 07 Dec 2005 09:29:00 -0700
Hi Michael
You said
* I chose the option, "use This Line" and selected Wave Out Mix
That's where you need to arrow around and find the What you hear choice.
Also, go into your Volume Control on your Pc. On the menu with the alt
key, you'll find properties. Go in there and look around. You can
change settings for playback and recording. If you select recording,
then when you exit the menu, you can tab around and change various
settings. If you select What you Hear instead of the line in, you can
set recording levels for the microphone, line in, etc separately.
Now, having said that, I don't know if it is dependent on your
particular sound card. I have a Soundblaster Audigy II card.
There is a good article in the ACBRadio Main Menu archives on using the
Volume Control. If you listen to that, it can probably describe it much
better than I did.
I think it was Jonathan Mosen who did it, and he specifically mentions
the What You Hear choice. So, give it a listen. There are also a few
good articles on their archive on Total Recorder, and you might find
them helpful as well.
Jean
----- Original Message -----
From: "Michael G." <commodore128@xxxxxxxxxxxxx>
To: <jfw@xxxxxxxxxxxxx>
Sent: Tuesday, December 06, 2005 3:38 PM
Subject: Re: question on recording audio with Total Recorder
Hi Jean,
I did manage to get it to record both the Jaws speech and the
microphone audio but I didn't find any option called "what you hear".
I do have another question though. How do I configure Total Recorder
to have the Microphone audio be louder than the Jaws audio. These are
the settings I used by the way:
Under Recording Source and Parameters
* I chose Sound Board
* I chose to record through Total Recorder
* I chose the option, "use This Line" and selected Wave Out Mix
I mention this just in case anyone else out there would like to try
this with Total Recorder 5.3.
Michael
----- Original Message -----
From: "Jean Menzies" <jemenzies@xxxxxxx>
To: <jfw@xxxxxxxxxxxxx>
Sent: Tuesday, December 06, 2005 4:09 PM
Subject: Re: question on recording audio with Total Recorder
Michael
When you load the program, press enter on the Recourding source and
parameters button. As you tab across, you'll find a combo box that
lists the sources for your recording. Move up and down and choose
What You Hear. This will record everything going through the sound
card including Jaws, music, etc. You likely have it on microphone
right now.
Jean
----- Original Message -----
From: "Michael G." <commodore128@xxxxxxxxxxxxx>
To: <jfw@xxxxxxxxxxxxx>
Sent: Tuesday, December 06, 2005 2:34 PM
Subject: question on recording audio with Total Recorder
Hi Guys,
Does anyone know how to record an audiomix of JAWS speech and
microphone input simultaneously? I'm trying to do this using Total
Recorder 5.3. I was trying to create an audio tutorial to submit to
the Main Menu web site but so far I can only record either the Jaws
speech or the microphone audio but not both at the same time. I want
to do this through the software or the sound card settings. I'd
rather not have to record the Jaws speech using the microphone. It
doesn't sound as clear when you do it that way. Any help would be
appreciated. Thanks!
Michael
--
To post a message to the list, send it to jfw@xxxxxxxxxxxxx
To unsubscribe from this mailing list, send a message to
jfw-request@xxxxxxxxxxxxx with the word unsubscribe in the subject
line.
Archives located at: //www.freelists.org/archives/jfw
If you have any concerns about the list, post received from the list,
or the way the list is being run, do not post them to the list.
Rather contact the list owner at jfw-admins@xxxxxxxxxxxxxx
--
To post a message to the list, send it to jfw@xxxxxxxxxxxxx
To unsubscribe from this mailing list, send a message to
jfw-request@xxxxxxxxxxxxx with the word unsubscribe in the subject
line.
Archives located at: //www.freelists.org/archives/jfw
If you have any concerns about the list, post received from the list,
or the way the list is being run, do not post them to the list. Rather
contact the list owner at jfw-admins@xxxxxxxxxxxxxx
--
To post a message to the list, send it to jfw@xxxxxxxxxxxxx
To unsubscribe from this mailing list, send a message to
jfw-request@xxxxxxxxxxxxx with the word unsubscribe in the subject line.
Archives located at: //www.freelists.org/archives/jfw
If you have any concerns about the list, post received from the list, or the way the list is being run, do not post them to the list. Rather contact the list owner at jfw-admins@xxxxxxxxxxxxxx
Other related posts:
