I have a separate licensing server setup for 2003 and can connect on my LAN to the 2003 terminal server. My problem is that I can't connect to it externally even though I have followed the same steps as I did for a windows 2000 Terminal server I have created a Protocol Definition for Inbound 3389 Created a Server publishing rule mapping this to the internal server I do not have Terminal services installed on the ISA server. I can connect to the IIS server and see the root under construction page and the Remote Desktop Connection page at www.mydomain.com/tsweb When I enter a server name I get the following error. I have seen this before while trying to configure TS access but can't remember what I did to correct it. "The client could not establish a connection to the remote computer. The most likely causes for this error are 1. Remote connections might not be enabled at the remote computer 2. The max no of connections was exceeded at the remote computer 3. A network error occurred while establishing the connection." Tried going back to the start and doing all the ISA config again but same result. Thanks for any help Joe -----Original Message----- From: Rogers, Brian [mailto:RogersB@xxxxxxxxxxxxxx] Sent: 26 August 2003 16:10 To: [ISAserver.org Discussion List] Subject: [isalist] RE: Publishing Terminal Server on Windows Server 2003 http://www.ISAserver.org Setup a licensing server? From what I read a win2k license server cannot issue licenses to a Win2k3 terminal server. Youll need a Win2k3 licensing server. -----Original Message----- From: Joseph Ledwidge [ mailto:josephl@xxxxxx] Sent: Tuesday, August 26, 2003 11:13 AM To: [ISAserver.org Discussion List] Subject: [isalist] Publishing Terminal Server on Windows Server 2003 http://www.ISAserver.org I am trying to publish TSAC on a windows 2003 server. I have successfully published a Win 2000 server this way and I am now trying to do this with ISA server installed on a windows 2003 server to a terminal server that is also on 2003 server. Has anyone had any problems doing this?? I have followed the instructions in the book (as per 2000) and on the website I can connect to the correct Web server but I am not able to connect to the remote desktop. Can anyone give me some ideas where I should look - Getting the usual error message saying server is unable to accept connections at this time etc?? Joe Ledwidge Systems Manager Metals Powders International Dublin Ireland ------------------------------------------------------ List Archives: http://www.webelists.com/cgi/lyris.pl?enter=isalist ISA Server Newsletter: http://www.isaserver.org/pages/newsletter.asp ISA Server FAQ: http://www.isaserver.org/pages/larticle.asp?type=FAQ ------------------------------------------------------ Other Internet Software Marketing Sites: Leading Network Software Directory: http://www.serverfiles.com No.1 Exchange Server Resource Site: http://www.msexchange.org Windows Security Resource Site: http://www.windowsecurity.com/ Network Security Library: http://www.secinf.net/ Windows 2000/NT Fax Solutions: http://www.ntfaxfaq.com ------------------------------------------------------ You are currently subscribed to this ISAserver.org Discussion List as: rogersb@xxxxxxxxxxxxxx To unsubscribe send a blank email to $subst('Email.Unsub') ------------------------------------------------------ List Archives: http://www.webelists.com/cgi/lyris.pl?enter=isalist ISA Server Newsletter: http://www.isaserver.org/pages/newsletter.asp ISA Server FAQ: http://www.isaserver.org/pages/larticle.asp?type=FAQ ------------------------------------------------------ Other Internet Software Marketing Sites: Leading Network Software Directory: http://www.serverfiles.com No.1 Exchange Server Resource Site: http://www.msexchange.org Windows Security Resource Site: http://www.windowsecurity.com/ Network Security Library: http://www.secinf.net/ Windows 2000/NT Fax Solutions: http://www.ntfaxfaq.com ------------------------------------------------------ You are currently subscribed to this ISAserver.org Discussion List as: josephl@xxxxxx To unsubscribe send a blank email to $subst('Email.Unsub')