[PCB_FORUM] Re: same net rules
- From: "westfeldt" <westfeldt_nbcd@xxxxxxxxx>
- To: <icu-pcb-forum@xxxxxxxxxxxxx>
- Date: Fri, 19 Jan 2007 17:14:58 -0700
Soldermask to soldermask might work, but I don't know how to set it, is that
available in Performance option?
-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Robert Szumowicz
Sent: Friday, January 19, 2007 8:24 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: same net rules
Hi all,
I think I do understand the question since I also miss such feature.
Problem stated:
- to not to have Via too close to SMD pin
Partial Solution:
- enable same net DRC (problem is that it checks all other rules and often
creates many unwanted DRCs)
Other possibility
- set a rule for "Solder mask to Solder mask" spacing assuming that Vias
are not covered (problem is that this is one global rule for a whole design)
regards,
Robert
Macindoe, Gary wrote:
> Hey Pat,
>
> Not exactly sure what you are asking here. Need a little clarification!
>
> Gary E. MacIndoe
> Advanced Micro Devices
> PCB Design Engineer
> Longmont, Colorado
>
> -----Original Message-----
> From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of westfeldt
> Sent: Friday, January 19, 2007 6:43 AM
> To: icu-pcb-forum@xxxxxxxxxxxxx
> Subject: [PCB_FORUM] same net rules
>
> Is there no way in Allegro to have the same net rules apply only to
> certain rules? The one I always need is via to smd pin, but I would
> not want all the rest of the rules to have same net application.
>
> Patrick Westfeldt, Jr.
> North Boulder Circuit Design
> westfeldt_nbcd@xxxxxxxxx
> 720-406-0887
> c 720-272-5822
>
>
> -----------------------------------------------------------
> To subscribe/unsubscribe:
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
> To view the archives of this list go to
> //www.freelists.org/archives/icu-pcb-forum/
>
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
>
>
>
>
> -----------------------------------------------------------
> To subscribe/unsubscribe:
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
> To view the archives of this list go to
> //www.freelists.org/archives/icu-pcb-forum/
>
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
>
>
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
Other related posts:
