Double Ditto! -----Original Message----- From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]On Behalf Of Macindoe, Gary Sent: Thursday, July 08, 2010 4:39 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias > I too like this forum better than the cadence one. faster, leaner and most of the time i get an answer. Ditto, I think there’s enough of us to keep it alive. Regards, Gary MacIndoe Senior PCB Layout Designer Contract - Kelly Services Covidien EbD R & D 5920 Longbow Drive Boulder, CO 80301 303.476.7458 www.covidien.com From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx Sent: Thursday, July 08, 2010 2:16 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias 16.3 does via removals. I too like this forum better than the cadence one. faster, leaner and most of the time i get an answer. sam -----Original Message----- From: Macindoe, Gary <Gary.Macindoe@xxxxxxxxxxxx> To: icu-pcb-forum@xxxxxxxxxxxxx Sent: Thu, Jul 8, 2010 10:14 am Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias Les, Maybe the Dangling Lines Report (Tools -> Reports) will give you the information you need. Like Joe said, if there are two vias in the same location, you should get a DRC error. Regards, Gary MacIndoeSenior PCB Layout DesignerContract - Kelly ServicesCovidien EbD R & D5920 Longbow DriveBoulder, CO 80301 303.476.7458www.covidien.com -----Original Message-----From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Les WongSent: Thursday, July 08, 2010 9:17 AMTo: icu-pcb-forum@xxxxxxxxxxxxxxxxxxxx: [PCB_FORUM] Re: Allegro 15.7 duplicate vias Jean-Charles I looked in the dbdoctor.log file but did not see any duplicate via messages ?Les --- On Thu, 7/8/10, JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx> wrote: > From: JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx>> Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias> To: icu-pcb-forum@xxxxxxxxxxxxx> Date: Thursday, July 8, 2010, 2:22 AM> Dave,> > i am also on cadence's community BUT _i_ considere this> "forum" more easyer to use each day...> > I have respond to somebody on cadence's community; this> person rspond and when i try to respond ... the web site> does nor allow me to...(internal error)> I think i would retry later... this is not first time i> have problems with cadence's site> > Emails NEVER fails; cadence's web site does.> And it bory me with log-in each time!> > THIS place is much more easier. When cadence's community> site will be much more userfreindly (less flash animations,> more reliebality) it will be a real good place> > Les,> > dbdoctor generates a log file: you can find in it the> coordonates of duplicated vias so you can remove them> manually.> > Jean-Charles> > Les Wong a écrit :> > Hi Dave> > Thanks,> > Les> > > > --- On *Wed, 7/7/10, David Elder /<dave.elder@xxxxxxxxxxxxx>/*> wrote:> > > > > > From: David Elder <dave.elder@xxxxxxxxxxxxx>> > Subject: Re: [PCB_FORUM]> Allegro 15.7 duplicate vias> > To: icu-pcb-forum@xxxxxxxxxxxxx> > Date: Wednesday, July 7, 2010,> 2:42 PM> > > > Hi Les,> > This forum doesn't> get much use any more. You might want to> > consider moving over to the> cadence community forum -> > http://www.cadence.com/community/forums/27.aspx> > Anyway - attached is> some code that identifies duplicate hits on> > holes and vias.> > Regards,> > Dave> > > > Dave Elder> > PCB Design Manager> > Tait Radio Communications> > 535 Wairakei Rd, PO Box 1645,> Christchurch> > DDI: +64 3 358-0327> > Mobile: +64 21 373725> > www.taitradio.com <http://www.taitradio.com>> > dave.elder@xxxxxxxxxxxxx> </mc/compose?to=dave.elder@xxxxxxxxxxxxx>> > TAIT: THE RIGHT FIT> > > > > > On 8 July 2010 06:10, Les Wong> <maveric0@xxxxxxxxxxx> > </mc/compose?to=maveric0@xxxxxxxxxxx>>> wrote:> > > > Hi All> > > > Dbcheck used to> removed duplicate vias, dbdoctor does not do> > this any more.> > How is everyone> dectecting and removing duplicate vias ?> > > > Thanks,> > Les> > > > > -----------------------------------------------------------> To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx> with a subject of subscribe or unsubscribe> > To view the archives of this list go to //www.freelists.org/archives/icu-pcb-forum/> > Problems or Questions:> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx> -----------------------------------------------------------> -----------------------------------------------------------To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxxxxxx a subject of subscribe or unsubscribe To view the archives of this list go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions:Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxxxxxx a subject of subscribe or unsubscribe To view the archives of this list go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions:Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx