iom 230,231,232,233 is superceded by V1.34 V1.33 was a limited release ________________________________________ From: Landry, Scott Sent: Friday, April 27, 2012 12:08 PM To: foxboro@xxxxxxxxxxxxx Subject: RE: [foxboro] FBM232 FDSI Configurator Joe, Also, The current driver is V2.2 and iom232 is V1.33 Regards, Scott ________________________________________ From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Landry, Scott [Scott.Landry@xxxxxxxxxxxx] Sent: Friday, April 27, 2012 12:04 PM To: foxboro@xxxxxxxxxxxxx Subject: Re: [foxboro] FBM232 FDSI Configurator Joe, If You want to use a "Device Configuration File" (.xml) in your ECB201 , I believe you will need to add +XML in DVOPTS. If no XML for ECB201 is required than leave FILEID blank. PLC comms can be tested to driver with B0700BU-D Chapter 7 FV disps/blocks with also adding Figure 4.3 Battery status rung and Time Sync rungs in PLC. With no XML in ECB201 DCIs can access PLC tag array directly , example NAME = MYCMPND_07:1PAK_IN23 TYPE = PAKIN DESCRP = MAP TO MYMCIN1_08:MOTI1_065 PERIOD = 1 PHASE = 0 LOOPID = IOM_ID = TESTCP_ECB:TST232 PKINGP = TSTAREA[1]:U4 PKIOPT = 1 PAKCIN = 0x20303020 UPDPER = 10000 SIMOPT = 0 END Regards, Scott L. Landry Invensys Operations Management Gulf Coast Service District, USA ________________________________________ From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Joseph M. Riccardi [Joe@xxxxxxxxxxxxx] Sent: Friday, April 27, 2012 11:00 AM To: foxboro@xxxxxxxxxxxxx Subject: Re: [foxboro] FBM232 FDSI Configurator My FDSI God, my God, why hast thou forsaken me? I appreciate the help from the list so far and I have made some progress. But after 2 days I still cannot communicate to 2 ControlLogix PLCs; FCP270 > FBM232 > ECB200 > ECB201 for each PLC. I have the ECB200s communicating and on-line but I cannot get the ECB201s to work. As soon as I Enable Communications they fail. Below are the ECB listings. Just FYI: * As near as I and our Elite Team of 4 can tell, we have followed all procedures and instructions despite some confusing and conflicting documentation. * My focus has been on the DEV_ID because that is where much of the confusing and conflicting documentation exists. It is also the Parameter on the Select Display for the ECB201 blocks that is highlighted in red along with the ECB Status (DEV FAIL) field. The other fields are a variety of greens and cyans. * To the best of our abilities, the variety of *.xml files have been created and downloaded properly. The names and details do show up in the SMDH Equip Info displays. * We have tried a variety of variations of ECB parameters and we have also tried unsuccessfully with and without a point and block configured. * I can ping the 2 FBM232s and the 2 PLCs. * In desperation I have Deleted and Undeleted everything; more than once. In further desperation I have even rebooted everything; more than once. Before I hang myself, does anyone see something wrong with the ECB configurations, or have any suggestions? Integrated Control Configurator Configuration = PC5AXX Fri Apr 27 10:43:18 2012 PC5AXX_ECB:PRIMARY_ECB NAME PRIMARY_ECB TYPE ECBP DESCRP NRBUS 2 BUSOPT 3 BUSTYP R PIOWDT 250 MPOLL 7 FIBER 0 BADALM 0 PC5AXX_ECB:PC5A03 NAME PC5A03 TYPE ECB200 DESCRP FBM232 LHM PLC PERIOD 1 PHASE 0 DEV_ID PC5A03 HWTYPE 232 SWTYPE 232 PORTEX 1 FILEID PC5A03.XML FSENAB 0 FSDLAY 1000 WDTMR 10 SFILID ETHERNETIP.ZIPH SYSCFG 1000 SYSOPT 0 PC5AXX_ECB:PC5A04 NAME PC5A04 TYPE ECB200 DESCRP FBM232 TFF PLC PERIOD 1 PHASE 0 DEV_ID PC5A04 HWTYPE 232 SWTYPE 232 PORTEX 1 FILEID PC5A04.XML FSENAB 0 FSDLAY 1000 WDTMR 10 SFILID ETHERNETIP.ZIPH SYSCFG 1000 SYSOPT 0 PC5AXX_ECB:LHMX03 NAME LHMX03 TYPE ECB201 DESCRP LHM PLC PERIOD 1 PHASE 0 DEV_ID LHMX03 HWTYPE 232 SWTYPE 232 PARENT PC5A03 DVNAME 192.168.1.115 DVADDR DVOPTS EIP/CLX+SN=0 PORTNO 1 FILEID LHMX03.XML SFILID MANFTR DVTYPE VERNUM ERROPT 0xFFFE PC5AXX_ECB:TFFX04 NAME TFFX04 TYPE ECB201 DESCRP TFF PLC PERIOD 1 PHASE 0 DEV_ID TFFX04 HWTYPE 232 SWTYPE 232 PARENT PC5A04 DVNAME 192.168.1.105 DVADDR DVOPTS EIP/CLX+SN=0 PORTNO 1 FILEID TFFX04.XML SFILID MANFTR DVTYPE VERNUM ERROPT 0xFFFE Joseph M. Riccardi 386-441-0250 Office 386-451-7607 Cell Joe@xxxxxxxxxxxxx "To give real service you must add something that cannot be bought or measured with money; and that is sincerity and integrity." - Donald A. Adams -----Original Message----- From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Joseph M. Riccardi Sent: Wednesday, April 25, 2012 8:03 PM To: foxboro@xxxxxxxxxxxxx Subject: [foxboro] FBM232 FDSI Configurator FDSI folks, I am trying to create a Port, Generic Ethernet xml file for a new FBM232. No matter what I enter, when I try to save the configuration, I get an error message "Exception has been thrown by the target of an invocation". Even if I open up an existing one and try to save it with no changes I get the same error message. What am I missing? The configuration parameters are too simple to mess up, there are just 2; Select FBM Type (FBM232) and the IP Address. Duh! Any suggestions? Nothing in the manual offers any help. Joseph M. Riccardi 386-441-0250 Office 386-451-7607 Cell Joe@xxxxxxxxxxxxx "To give real service you must add something that cannot be bought or measured with money; and that is sincerity and integrity." - Donald A. Adams _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave *** Confidentiality Notice: This e-mail, including any associated or attached files, is intended solely for the individual or entity to which it is addressed. This e-mail is confidential and may well also be legally privileged. If you have received it in error, you are on notice of its status. Please notify the sender immediately by reply e-mail and then delete this message from your system. Please do not copy it or use it for any purposes, or disclose its contents to any other person. This email comes from a division of the Invensys Group, owned by Invensys plc, which is a company registered in England and Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For a list of European legal entities within the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx. You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject to the terms of any agreements between Invensys (and/or its subsidiaries and affiliates) and the recipient (and/or its subsidiaries and affiliates). _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave *** Confidentiality Notice: This e-mail, including any associated or attached files, is intended solely for the individual or entity to which it is addressed. This e-mail is confidential and may well also be legally privileged. If you have received it in error, you are on notice of its status. Please notify the sender immediately by reply e-mail and then delete this message from your system. Please do not copy it or use it for any purposes, or disclose its contents to any other person. This email comes from a division of the Invensys Group, owned by Invensys plc, which is a company registered in England and Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For a list of European legal entities within the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx. You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject to the terms of any agreements between Invensys (and/or its subsidiaries and affiliates) and the recipient (and/or its subsidiaries and affiliates). _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave