Re: [foxboro] FBM231 RS485 COMMUNICATION
- From: RAKESH DASH <rakeshinxs@xxxxxxxxx>
- To: foxboro@xxxxxxxxxxxxx
- Date: Mon, 2 Jul 2012 01:16:20 +0530
Angel/Sahara,
Yes, I have 43001:F4. Sorry I mistyped it. There are three different types
of devices communicating. Port1 and Port2 device are fine and data also is
received.
The device which is a electric meter & connected to Port3 is unable to
communicate. Rather in SMDH it shows me healthy if I don't configure any
points in IACC. As soon as I configure a floating point, & download, the
SMDH says "Device Failed".
So not sure what I am missing. Gerrit has suggested few things to check
which I will try.
Any other help on the subject is appreciated
Thanks !!
- Rakesh
On Sun, Jul 1, 2012 at 9:49 PM, Dominguez, Angel <
angel.dominguez@xxxxxxxxxxxx> wrote:
> There's two address format 5 or 6 digits, you should have 43001:F4 as a
> valid format.
> Angel Dominguez
> 938 136-8842
> -----Original Message-----
> From: ש×?ר קצ×?
> Sent: 01/07/2012, 11:16
> To: foxboro@xxxxxxxxxxxxx
> Subject: Re: [foxboro] FBM231 RS485 COMMUNICATION
>
> Hi, does the problem is that you can't configure all the ports?
> Shahar chemada fine chemicals
>
> -----Original Message-----
> From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx]
> On Behalf Of RAKESH DASH
> Sent: Saturday, June 30, 2012 8:53 PM
> To: foxboro@xxxxxxxxxxxxx
> Subject: [foxboro] FBM231 RS485 COMMUNICATION
>
> Hi there,
> I am trying to interface FBM231 with an external device over RS485.
> The modbus data is Holding Register Floating Point (4 bytes)
> I checked the communication and data using modscan in a laptop and all is
> good.
> The configuration in FDSI baud rate etc. is also fine
>
> FBM231 is showing healthy on communication.
> But As soon as I define even one signal in the RIN block in the compound
> for receiving the data & download, the FBM231 goes out of order and shows
> me as device failed.
> I have configured the point address PNT_NO as 430001:F4.
>
> I there any known issue of such kind ? Does the FBM231 support floating
> point signals ?
> I am stuck with this and I have to wind this up by Tuesday. Any help on the
> subject is appreciated. Thanks !!
>
> Regards,
> - Rakesh
>
>
>
>
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process
> Systems (formerly The Foxboro Company). Use the info you obtain here at
> your own risks. Read http://www.thecassandraproject.org/disclaimer.html
>
> foxboro mailing list: //www.freelists.org/list/foxboro
> to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>
>
>
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process
> Systems (formerly The Foxboro Company). Use the info you obtain here at
> your own risks. Read http://www.thecassandraproject.org/disclaimer.html
>
> foxboro mailing list: //www.freelists.org/list/foxboro
> to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>
>
>
> *** Confidentiality Notice: This e-mail, including any associated or
> attached files, is intended solely for the individual or entity to which it
> is addressed. This e-mail is confidential and may well also be legally
> privileged. If you have received it in error, you are on notice of its
> status. Please notify the sender immediately by reply e-mail and then
> delete this message from your system. Please do not copy it or use it for
> any purposes, or disclose its contents to any other person. This email
> comes from a division of the Invensys Group, owned by Invensys plc, which
> is a company registered in England and Wales with its registered office at
> 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023).
> For a list of European legal entities within the Invensys Group, please go
> to http://www.invensys.com/en/legal/default.aspx.
>
> You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
> reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be
> subject to the terms of any agreements between Invensys (and/or its
> subsidiaries and affiliates) and the recipient (and/or its subsidiaries and
> affiliates).
>
>
>
>
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process
> Systems (formerly The Foxboro Company). Use the info you obtain here at
> your own risks. Read http://www.thecassandraproject.org/disclaimer.html
>
> foxboro mailing list: //www.freelists.org/list/foxboro
> to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>
>
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
Other related posts:
