Sounds like the t/a and/or t/a cable is bad or the wrong type ________________________________________ From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Dirk Pauwels [dirk.pauwels@xxxxxxxxxx] Sent: Wednesday, January 18, 2012 10:59 AM To: foxboro@xxxxxxxxxxxxx Subject: Re: [foxboro] FBM204 failed to be recognized by system Did you try delete and undelete? Did you try to delete the FBM in the CP60_ECB and create it again? If you created the FBM ECB's long time before you physically entered the fbms it might be necessary to re-create them Rgds, Dirk -----Original Message----- From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Jason.LJZ Sent: Wednesday, January 18, 2012 2:49 PM To: foxboro@xxxxxxxxxxxxx Subject: Re: [foxboro] FBM204 failed to be recognized by system I am sure we have set the IOMOPT = 1 IOM_ID SCI=3/SCO=3 etc. correctly. Thanks for your precious time and reply. 于 2012-1-18 16:29, Dirk Pauwels 写道: > > Q1: If your FBM is online and on scan it should be ok I guess > Q2: not that I know off, we have plenty of them and can't remember we > had problems during install > Q3: Did you enter the IOM_ID and point nr? > IOMOPT = 1? > Did you enter the SCI=3/SCO=3? > > Rgds, > Dirk > > -----Original Message----- > From: foxboro-bounce@xxxxxxxxxxxxx > [mailto:foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of Jason.LJZ > Sent: Wednesday, January 18, 2012 11:28 AM > To: foxboro@xxxxxxxxxxxxx > Subject: [foxboro] FBM204 failed to be recognized by system > > Dear all, > > I just ran into a problem: we need to add a FBM204 to our system, which is > I/A 7.0 with 4 pairs CP60 and six AW51/WP51(Sun Blade 150) stations. > > Before we added the FBM204, the system has no other FBM204 installed. We > added a ECB2 and configured it as HWTYPE=204, SWTYPE=2. AIN and AOUT were > added and configured. > > The status of ECB2 was ONLINE and ON_SCAN. > > The problem is when we checked the AIN and AOUT block, the AIN block was > indicated as BAD I/O even the transmitter outside worked normally. When we > set output of AOUT as 50%, no milliampere can be measured. > > We also added a FBM241C to our system, and it works fine once it was added. > The difference is there are FBM241C already used in system. > > My question is: > > 1. Does it matter that there are same type FBM already installed in system? > So the newly added modules can be recognized by system? > > 2. Is there any thing special about adding FBM204 to system? > > 3. What can I do to probably solve the problem? > > Thanks in advance for your precious time for reading this and any help is > appreciated. > > > ______________________________________________________________________ > _ This mailing list is neither sponsored nor endorsed by Invensys > Process Systems (formerly The Foxboro Company). Use the info you > obtain here at your own risks. Read > http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > > > ______________________________________________________________________ > _ This mailing list is neither sponsored nor endorsed by Invensys > Process Systems (formerly The Foxboro Company). Use the info you > obtain here at your own risks. Read > http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave *** Confidentiality Notice: This e-mail, including any associated or attached files, is intended solely for the individual or entity to which it is addressed. This e-mail is confidential and may well also be legally privileged. If you have received it in error, you are on notice of its status. Please notify the sender immediately by reply e-mail and then delete this message from your system. Please do not copy it or use it for any purposes, or disclose its contents to any other person. This email comes from a division of the Invensys Group, owned by Invensys plc, which is a company registered in England and Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For a list of European legal entities within the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx. You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject to the terms of any agreements between Invensys (and/or its subsidiaries and affiliates) and the recipient (and/or its subsidiaries and affiliates). _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave