Re: [foxboro] FBM204 failed to be recognized by system

  • From: "Jason.LJZ" <jason.ljz@xxxxxxxxx>
  • To: foxboro@xxxxxxxxxxxxx
  • Date: Wed, 18 Jan 2012 16:49:19 +0300

I am sure we have set the

IOMOPT = 1
IOM_ID
SCI=3/SCO=3

etc. correctly.

Thanks for your precious time and reply.

于 2012-1-18 16:29, Dirk Pauwels 写道:
>
> Q1: If your FBM is online and on scan it should be ok I guess
> Q2: not that I know off, we have plenty of them and can't remember we had 
> problems during install
> Q3: Did you enter the IOM_ID and point nr?
> IOMOPT = 1?
> Did you enter the SCI=3/SCO=3?
>
> Rgds,
> Dirk
>
> -----Original Message-----
> From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On 
> Behalf Of Jason.LJZ
> Sent: Wednesday, January 18, 2012 11:28 AM
> To: foxboro@xxxxxxxxxxxxx
> Subject: [foxboro] FBM204 failed to be recognized by system
>
> Dear all,
>
> I just ran into a problem: we need to add a FBM204 to our system, which is 
> I/A 7.0 with 4 pairs CP60 and six AW51/WP51(Sun Blade 150) stations.
>
> Before we added the FBM204, the system has no other FBM204 installed. We 
> added a ECB2 and configured it as HWTYPE=204, SWTYPE=2. AIN and AOUT were 
> added and configured.
>
> The status of ECB2 was ONLINE and ON_SCAN.
>
> The problem is when we checked the AIN and AOUT block, the AIN block was 
> indicated as BAD I/O even the transmitter outside worked normally. When we 
> set output of AOUT as 50%, no milliampere can be measured.
>
> We also added a FBM241C to our system, and it works fine once it was added.
> The difference is there are FBM241C already used in system.
>
> My question is:
>
> 1. Does it matter that there are same type FBM already installed in system? 
> So the newly added modules can be recognized by system?
>
> 2. Is there any thing special about adding FBM204 to system?
>
> 3. What can I do to probably solve the problem?
>
> Thanks in advance for your precious time for reading this and any help is 
> appreciated.
>
>
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process 
> Systems (formerly The Foxboro Company). Use the info you obtain here at your 
> own risks. Read http://www.thecassandraproject.org/disclaimer.html
>
> foxboro mailing list:             //www.freelists.org/list/foxboro
> to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>
>
>
> _______________________________________________________________________
> This mailing list is neither sponsored nor endorsed by Invensys Process
> Systems (formerly The Foxboro Company). Use the info you obtain here at
> your own risks. Read http://www.thecassandraproject.org/disclaimer.html
>
> foxboro mailing list:             //www.freelists.org/list/foxboro
> to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
> to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
>
 
 
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
 
foxboro mailing list:             //www.freelists.org/list/foxboro
to subscribe:         mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe:      mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
 

Other related posts: