In the sonar audio control panel (options menu \ audio) there are driver
settings on the last tab. The correct driver needs to show in that list,
and you also need to be sure it's name is checked in both the input and
the output lists. You then need to go back to the first tab and be sure
that both the play and record devices are set to the new device.
Also, driver installation can be a bit strange sometimes. I have an
Edirol quad capture, and when installing the device drivers, you need to
disconnect the hardware until you are prompted to plug it in; if you
have it plugged in when you begin the installation then it may not work
properly. I have no idea if your drivers require this, but it might be
worth checking.
Hope that helps.
-- Rich
On 11/21/2017 1:50 PM, Austin Beaumount (Redacted sender beaumount for
DMARC) wrote:
I updated the driver. Now I can see the 2I2 device in sonar but, nothing I can
hear. I did apply acio in driver mode, and input and output all selected 2I2,
then I re-start computer, open sonar again, showing midi device not setup. I
don’t get it, I did these procedures for three times.
Best Wish
Austin Beaumount
--------------------------------------------
On Tue, 11/21/17, DJX <megamansuperior@xxxxxxxxxxx> wrote:
Subject: [ddots-l] Re: 2I2 audio device problem
To: "ddots-l@xxxxxxxxxxxxx" <ddots-l@xxxxxxxxxxxxx>
Date: Tuesday, November 21, 2017, 10:14 AM
Does it also say Code 10?
What category are you seeing it
in, sounds and audio or other devices?
Looks like your drivers are the
issue.
Regards, DJX
From:
ddots-l-bounce@xxxxxxxxxxxxx
<ddots-l-bounce@xxxxxxxxxxxxx> on behalf of Austin
Beaumount <dmarc-noreply@xxxxxxxxxxxxx>
Sent: Tuesday, November 21, 2017 1:10:34 PM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: 2I2 audio device
problem
Oho, it
showing “this device cannot start".
Best Wish
Austin Beaumount
--------------------------------------------
On Tue, 11/21/17, DJX <megamansuperior@xxxxxxxxxxx>
wrote:
Subject: [ddots-l] Re: 2I2 audio device problem
To: "ddots-l@xxxxxxxxxxxxx"
<ddots-l@xxxxxxxxxxxxx>
Date: Tuesday, November 21, 2017, 10:01 AM
Press enter on the 2i2 in device
manager, does it say "this device is working
properly"?
Regards, DJX
From:
ddots-l-bounce@xxxxxxxxxxxxx
<ddots-l-bounce@xxxxxxxxxxxxx> on behalf of
Austin
Beaumount <dmarc-noreply@xxxxxxxxxxxxx>
Sent: Tuesday, November 21, 2017 12:52:56 PM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: 2I2 audio device
problem
I
downloaded from
https://eur03.safelinks.protection.outlook.com/?url=https%3A%2F%2Fus.focusrite.com%2Fdownloads%2Ffocusrite-usb-asio-driver-4364-windows&data=02%7C01%7Cmegamansuperior%40hotmail.com%7C61078b5f8bd940864d3508d53108b979%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636468835912672458&sdata=1PqLHZlIK%2BltPE5LqzIp6b8mTn%2B0HdnbnzEKG7HaOUw%3D&reserved=0
the file name is focusriteusbinstaller4.36.4-484.exe.
I use three USB port, one for midi keyboard M-audio88,
one
for computer wireless keyboard and last one is audio
device
2I2.
I can see focusrite usb asio driver in control panel,
program & feature, it also showing device manager.
Best Wish
Austin Beaumount
--------------------------------------------
On Tue, 11/21/17, DJX
<megamansuperior@xxxxxxxxxxx>
wrote:
Subject: [ddots-l] Re: 2I2 audio device problem
To: "ddots-l@xxxxxxxxxxxxx"
<ddots-l@xxxxxxxxxxxxx>
Date: Tuesday, November 21, 2017, 8:15 AM
Hi, is the driver you downloaded
for the second gen? I believe they use different
drivers/control panels.
The second gen is
compatible, I built a daw for a client last year and
that
was the audio interface I installed and it worked
great
in
SONAR. She's still using it to this day.
Do you hear the hardware
inserted sound when you plug in the unit?
Also, how many things do you have plugged in to
your USB ports? Are you using a USB hub?
HTH, DJX
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx
[mailto:ddots-l-bounce@xxxxxxxxxxxxx]
On Behalf Of Austin Beaumount
Sent: Tuesday,
November 21, 2017 10:32 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: 2I2 audio device
problem
I remove zoom R16
driver then installed focusrite 2I2 usb asio driver
(this
version was release in June 2017) but, nothing found
in
sonar, option, audio, input/output. I did re-selected
acio
in driver mode then click apply, there’s nothing I
can
choose in device selection. I bought this 2I2 is
second
generation, do you think is not compatible? I checked
Cakewalk website it only show how to setup 2I2 first
generation with sonar.
Best Wish
Austin Beaumount
--------------------------------------------
On Mon, 11/20/17, Austin Beaumount
<dmarc-noreply@xxxxxxxxxxxxx>
wrote:
Subject: [ddots-l]
2I2 audio device problem
To: "dancing
dots" <ddots-l@xxxxxxxxxxxxx>
Date: Monday, November 20, 2017, 4:19 PM
Hello all,
I was use zoom r16 for audio output
monitoring. Today, I switch to 2I2 when I open
sonar I got a message no audio output. I go to menu
option, then audio, there’s no any audio
selection,
the
box is 0 nothing I can choose. Does anyone can
help?
Best Wish
Austin Beaumount
PLEASE READ THIS FOOTER AT
LEAST ONCE!
To leave the list, click on
the
immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe
If this link doesn't work then send a
message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such
as
vacation mode,
click on
the immediately following
link:
ddots-l-request@xxxxxxxxxxxxx?subject
q
or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
PLEASE READ THIS
FOOTER AT LEAST ONCE!
To leave the list,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If
this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list
commands such as vacation mode, click on the
immediately
following link:
ddots-l-request@xxxxxxxxxxxxx?subject
q or send a message, to ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type faq
<� HDD
4�!!N912�$�4!
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following
link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject�q or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following
link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject�q or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject�q or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
