[argyllcms] DTP20 in un-tethered mode

  • From: "Martin Weberg" <martin.weberg@xxxxxxxxx>
  • To: argyllcms@xxxxxxxxxxxxx
  • Date: Fri, 6 Jul 2007 23:02:07 +0200

Hi again,

Now, I tried the un-tethered operation. Got errors, see log.

Memory cleared. Unit calibrated. TID strip read. After the last strip the
green diode was pulsing slow (chart completed).
Then:
printread -v -d3_g21_m5_f1680

Steps in each Pass = 30
Passes in each Strip = 18, 19, 19
dtp20: About to init coms
dtp20: About to init USB
icoms: About to set usb port characteristics
icoms: About to open the USB port
icoms: USB port needs opening
icoms: About to open USB port 'usb:/bus1/dev1 (Xrite DTP20)'
icoms: USB port is now open
icoms: Clearing any USB errors
icoms: usb port characteristics set ok
dtp20: Sending '0PR^M'response '<00>^M^J' ICOM err 0x0
dtp20: Sending '0PR^M'response '<00>^M^J' ICOM err 0x0
dtp20: Sending '^M'response '<00>^M^J' ICOM err 0x0
dtp20: Sending 'GI^M'response 'Instrument Type:       DTP20^M^JSerial
Number:
     005297^M^JMain Date Code:        FB01^M^JMain Version:          1.03
^M^JBo
ot Version:          1.03^M^J<00>^M^J' ICOM err 0x0
Instrument Type:       DTP20
Serial Number:         005297
Main Date Code:        FB01
Main Version:          1.03
Boot Version:          1.03
dtp20: Got coms OK
dtp20: Sending '0PR^M'response '<00>^M^J' ICOM err 0x0
dtp20: Sending '0008CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending 'SV^M'response 'X-Rite DTP20 vFB01^M<00>^M' ICOM err 0x0
dtp20: Sending '0101CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '0005CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '0207CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '020ACF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '0518CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '001ACF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '0416CF^M'response '<00>^M' ICOM err 0x0
dtp20: Sending '00GM^M'response '0^M<00>^M' ICOM err 0x0
dtp20: Sending 'CS^M'response '03^M<00>^M' ICOM err 0x0
dtp20: Sending 'ST^M'response 'Strip Length:  30^MTotal Patches: 1680^MPatch
Wid
th:   6.5 mm^MGap Width:     0.0 mm^MUser  1:       0^MUser  2:
3^MUser  3
:       1^MUser  4:       1^MUser  5:       5^MUser  6:       0^MUser  7:
0^MUser  8:       0^MUser  9:       0^MUser 10:       0^M<00>^M' ICOM err
0x0
About to read strip pass A
Trigger instrument switch or any key to start, Esc, ^C or Q to give
up:dtp20: Se
nding 'CS^M'response '03^M<00>^M' ICOM err 0x0

Strip read failed due to misread (Trying to read strips when there is
already
an offline chart partially read. Clear the instrument and try again)
Hit Esc to give up, any other key to retry:
icoms: delete called
icoms: closing port
usb_close_port() called
usb port has been released and closed

Regards
Martin Weberg

Other related posts: