[access-uk] Re: Microsofts AntiSpyware
- From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx>
- To: <access-uk@xxxxxxxxxxxxx>
- Date: Wed, 15 Jun 2005 10:12:53 +0100
Start, All Programs, Microsoft AntiSpyware, Microsoft
AntiSpyware.
Click on the link "Spyware Scan Options", the look for the
Radio Button "Run a full system scan" followed by three
check boxes.
George.
> -----Original Message-----
> From: access-uk@xxxxxxxxxxxxx
> [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of Darran Ross
> Sent: 14 June 2005 22:09
> To: access-uk@xxxxxxxxxxxxx
> Subject: [access-uk] Re: Microsofts AntiSpyware
>
> Thanks Phil, that worked a treat, but has raised another
> question! Can anyone tell me how to get into Microsoft's
Anti
> Spyware to change the scan settings?
>
> During initial setup I chose the deep scan version,
reckoned
> to take around 30 minutes. However, when the scan took
place,
> it was the shorter 2 minute version.
>
> I've had a look through the options I can access, but
haven't
> been able to find were the change should be made.
>
> Regards.
>
> Darran
>
>
>
>
>
> ----- Original Message -----
> From: "Stephenson, Phil" <phil.stephenson@xxxxxxxxx>
> To: <access-uk@xxxxxxxxxxxxx>
> Sent: Tuesday, June 14, 2005 9:10 AM
> Subject: [access-uk] Re: Microsofts AntiSpyware
>
>
> | Hi Darren,
> |
> | I've used this software a bit and the way I launch a
scan is by
> | accessing the system tray with Insert f11 and then going
onto MS
> | Antispyware and then selecting the 'run scan' option -
> presuming you're
> | a jaws user.
> |
> | HtH
> |
> | Phil
> |
> |
> |
> | -----
> | Phil Stephenson
> | Disability Officer
> | Tel: 0115 8484495
> |
> | -----Original Message-----
> | From: access-uk@xxxxxxxxxxxxx
> [mailto:access-uk@xxxxxxxxxxxxx] On Behalf
> | Of Darran Ross
> | Sent: 13 June 2005 16:10
> | To: Access-UK
> | Subject: [access-uk] Microsofts AntiSpyware
> |
> | Hi List.
> |
> | I've now downloaded and installed this program, and have
> just come up
> | against my first problem.
> |
> | Using the JAWS cursor I've been able to stumble my way
through
> | installation etc. I've now come to the final screen,
where
> you're asked
> | to select the type of scan you want and then to press
"Run Scan Now"
> | button to begin. This is were I've come to a brick wall,
I
> can't find
> | any way to start the scan.
> | Again, using JAWS cursor, I've tried every possible
option
> to click on,
> | but still the scan hasn't started.
> |
> | Can someone please tell me how to locate this "Run Scan
Now" button?
> |
> | Using JAWS 5.1 with XP.
> |
> | Thanks.
> |
> | Darran
> |
> |
> |
> |
> |
> |
> | ** To leave the list, click on the immediately-following
link:-
> | **
[mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
> | ** If this link doesn't work then send a message to:
> | ** access-uk-request@xxxxxxxxxxxxx
> | ** and in the Subject line type
> | ** unsubscribe
> | ** For other list commands such as vacation mode, click
on the
> | ** immediately-following link:-
> | ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
> | ** or send a message, to
> | ** access-uk-request@xxxxxxxxxxxxx with the Subject:-
faq
> |
> |
> |
> | This email is intended solely for the addressee. It may
> contain private
> and confidential information. If you are not the intended
> addressee, please
> take no action based on it nor show a copy to anyone. In
> this case, please
> reply to this email to highlight the error. Opinions and
> information in
> this email that do not relate to the official business of
> Nottingham Trent
> University shall be understood as neither given nor
endorsed by the
> University.
> | Nottingham Trent University has taken steps to ensure
that
> this email and
> any attachments are virus-free, but we do advise that the
> recipient should
> check that the email and its attachments are actually
virus
> free. This is
> in keeping with good computing practice.
> |
> |
> | ** To leave the list, click on the immediately-following
link:-
> | **
[mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
> | ** If this link doesn't work then send a message to:
> | ** access-uk-request@xxxxxxxxxxxxx
> | ** and in the Subject line type
> | ** unsubscribe
> | ** For other list commands such as vacation mode, click
on the
> | ** immediately-following link:-
> | ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
> | ** or send a message, to
> | ** access-uk-request@xxxxxxxxxxxxx with the Subject:-
faq
> |
> |
>
>
> ** To leave the list, click on the immediately-following
link:-
> **
[mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
> ** If this link doesn't work then send a message to:
> ** access-uk-request@xxxxxxxxxxxxx
> ** and in the Subject line type
> ** unsubscribe
> ** For other list commands such as vacation mode, click on
the
> ** immediately-following link:-
> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
> ** or send a message, to
> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
>
>
** To leave the list, click on the immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** access-uk-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
Other related posts:
