[access-uk] Re: INDEX D QUESTION
- From: "Richard Godfrey-McKay" <richard@xxxxxxxxxxxxxxxxxxx>
- To: <access-uk@xxxxxxxxxxxxx>
- Date: Sun, 31 Jul 2011 18:39:04 +0100
Brian, Very many thanks. It would have taken hours to figure that without a
manual!
All done now.
Richard
Richard Godfrey-McKay
Telephone: 01738-445 880
Mobile: 07791 452 593
_____
From: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of
Brian Cairnie
Sent: 31 July 2011 16:19
To: access-uk@xxxxxxxxxxxxx
Subject: [access-uk] Re: INDEX D QUESTION
Hi Richard,
It sounds like a version 2, the version 3's have USB and network
connectivity as well.
First, you will need to get the paper length in inches rather than
centimetres.
Setting the paper length is a two stage process, you first set the whole
number of inches and then the fractional part. There are two settings,
paper length 1 and paper length 2. Paper length 1 is whole inches and paper
length 2 is any fractional part.
Towards the right hand end of the control panel on the embosser, there is a
button marked SETUP (it has SU in Braille as far as I remember)
The embosser will echo Change Setup (a, b or c depending on which one is
currently loaded)
To the right of the setup key you have just pressed, there is another key
marked Group
Press this repeatedly until the embosser says Page Layout
Just to the right of the Group key is the Item key
Press this repeatedly until the embosser says Paper Length 1
To the right of the Item key is the Value key. The first time you press
this, the embosser will tell you the current value, which in this case is
the paper length in whole inches.
If this matches the paper length, press the Item key once and the embosser
will say Paper Length 2, if your paper is different, press the Value key
repeatedly until it echoes the correct number of inches, when it does, press
the Item key once
Now press the Value key once which echoes the additional paper length, for
example it might say one quarter or one half. Again, if this matches your
paper length, press the Setup key to save any changes. If it doesn't match
you paper length, press the Value key until it does.
I know this sounds very long-winded, but it is much quicker to do than to
write down.
If you have any problems, please give me a call tomorrow between 9:30 am and
5:30 pm.
Thanks.
Brian Cairnie
Description: Description: Cragside Accessability 03
Cragside AccessABILITY Limited
Telephone: 0844 500 7091
Fax: 0844 500 7098
DotLine: 0844 500 7099
Skype: cragside_accessabilty
Email: info@xxxxxxxxxxxx
Web: www.cragside.com <http://www.cragside.com/>
P O Box 469, Sevenoaks, Kent, TN13 9JJ (Not for deliveries please)
Description: DNS+Index
----------------------------------------------------------------------------
---------------------------------------------
This email and files transmitted with it are confidential and intended
solely for the use of the individual or entity to whom they are addressed.
If you are not the named recipient, or have received this in error, please
notify Cragside AccessABILITY Limited immediately by telephone and delete
this email: do not disclose the contents to any other person or copy or
store the contents. Whilst every reasonable precaution has been taken,
Cragside AccessABILITY Limited cannot accept liability for any damage which
you sustain as a result of software viruses that may be contained in or
attached to this email.
THINK BEFORE YOU PRINT... THINK GREEN
From: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of
Richard Godfrey-McKay
Sent: 31 July 2011 15:51
To: access-uk@xxxxxxxxxxxxx
Subject: [access-uk] Re: INDEX D QUESTION
Hi Brian, My son couldn't see any visual indication of this. It must date
from about 2002, has the serial interface and says "Basic 4.0" when it fires
up.
Is that any help?
Thanks,
Richard
Richard Godfrey-McKay
Telephone: 01738-445 880
Mobile: 07791 452 593
_____
From: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of
Brian Cairnie
Sent: 31 July 2011 15:11
To: access-uk@xxxxxxxxxxxxx
Subject: [access-uk] Re: INDEX D QUESTION
Hi Richard,
Is it a model 2 or model 3 embosser?
Brian Cairnie
Description: Description: Cragside Accessability 03
Cragside AccessABILITY Limited
Telephone: 0844 500 7091
Fax: 0844 500 7098
DotLine: 0844 500 7099
Skype: cragside_accessabilty
Email: info@xxxxxxxxxxxx
Web: www.cragside.com <http://www.cragside.com/>
P O Box 469, Sevenoaks, Kent, TN13 9JJ (Not for deliveries please)
Description: DNS+Index
----------------------------------------------------------------------------
---------------------------------------------
This email and files transmitted with it are confidential and intended
solely for the use of the individual or entity to whom they are addressed.
If you are not the named recipient, or have received this in error, please
notify Cragside AccessABILITY Limited immediately by telephone and delete
this email: do not disclose the contents to any other person or copy or
store the contents. Whilst every reasonable precaution has been taken,
Cragside AccessABILITY Limited cannot accept liability for any damage which
you sustain as a result of software viruses that may be contained in or
attached to this email.
THINK BEFORE YOU PRINT... THINK GREEN
From: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of
Richard Godfrey-McKay
Sent: 31 July 2011 13:49
To: access-uk@xxxxxxxxxxxxx
Subject: [access-uk] INDEX D QUESTION
Hi, I've just received some tractor feed paper for this, and it's a
different length from my usual. Paper size is 32.3cm x 28cm.
Have altered the Brailemaker number of lines per page to 24, but think I
probably need to alter some embosser setting too. Can't find the manual
now, and would welcome some guidance please.
Richard
Richard Godfrey-McKay
Telephone: 01738-445 880
Mobile: 07791 452 593
Other related posts:
