thanks jim i didn't even check the voltage on that page. so therefore there is a pulse on the flyback thats missing and i think that is going to be the problem. a vertical pulse to micro is missing hopefully that's the problem just a diode a resistor, and a transistor to change and i'll know. will post fix. thanks again i was going around in circles.and thanks to damon who earlier said 129 sounded right. al marquardt ampm@xxxxxxx ----- Original Message ----- From: "Jim Myers" <jr.myers@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, November 30, 2001 11:46 AM Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > Al, the schematic calls for 140v when looking at the power supply section > but the dc voltage at the HOT collector says 129v, 129v is common on any > philips tv since very early C8 and C9 chassis so unless you have some > symptom you are trying to fix, which you haven't mentioned or I missed, I'd > say the 129v is right and the 140v is just another common error. > Jim Myers > jr.myers@xxxxxxxxxxx > ----- Original Message ----- > From: "al m" <ampm@xxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Friday, November 30, 2001 11:56 AM > Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > > > > > last try on this one . does anyone know what the b+ is supposed to be on > > this model manual calls for 140v , 11v 16v. i have 129v 9v, 13v. the > > regulator monitors the 11 volt line. i raised the 11 v line to 13v and the > > feed back curcuit turned the output voltage down. which tells me the > curcuit > > could be working. then why is the voltage low on the outputs. checked > > reference voltage on the regulator and everything seems normal.look below > > for more info. > > al marquardt > > ampm@xxxxxxx > > ----- Original Message ----- > > From: "al m" <ampm@xxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Thursday, November 29, 2001 7:16 AM > > Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > > > > > > > > > that is the problem it could be an error on the manual, but i'm starting > > to > > > think the regulator isn't working right. > > > al marquardt > > > ampm@xxxxxxx > > > ----- Original Message ----- > > > From: "Damon" <DAMON101@xxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Wednesday, November 28, 2001 7:37 PM > > > Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > > > > > > > > > > > > > I think the 129 volts you're getting is normal, 140 volts is not. > > > > Damon Brunger > > > > damon101@xxxxxxxxxxxxxx > > > > Telrad Electronic Services > > > > Ft Wayne, IN 46815 > > > > ----- Original Message ----- > > > > From: "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> > > > > To: <techassist@xxxxxxxxxxxxx> > > > > Sent: Wednesday, November 28, 2001 2:15 PM > > > > Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > > > > > > > > > > > > > > > > > You didn't say whats wrong with unit. > > > > > Phillip R Hull > > > > > phil245@xxxxxxxxxxxxx > > > > > ----- Original Message ----- > > > > > From: "al m" <ampm@xxxxxxx> > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > Sent: Wednesday, November 28, 2001 1:23 PM > > > > > Subject: [TechAssist] magnovox ts2575 25f800 chassis > > > > > > > > > > > > > > > > > > > > > > i'm stuck on this one. manual calls for 140v on main output on > > > > > regulator.i > > > > > > got 129v checked all outputs for caps and diodes regulator has > > > correct > > > > > > voltage on every pin. manual says turn down ac voltage and check > > > > > > outputs,same thing did anyone see this before the troubleshooting > > > guide > > > > is > > > > > > vague on what to do, it doesn't tell what to check if the voltages > > are > > > > > wrong > > > > > > only if they're not there. any tricks would be appreciated been on > > > this > > > > a > > > > > > long time and am in the same spot duh!!!!! > > > > > > al marquardt > > > > > > ampm@xxxxxxx > > > > > > > > > > > > > > > > > > ================================= > > > > > > Help make your TechAssist database better! > > > > > > Submit your fixes here: > http://circuitwork.com/techassist/tip/#tips > > > > > > ================================= > > > > > > To UNSUBSCRIBE your email address, click here: > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > > > > > > > > ================================= > > > > > Help make your TechAssist database better! > > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > > ================================= > > > > > To UNSUBSCRIBE your email address, click here: > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > > > > ================================= > > > > Help make your TechAssist database better! > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > ================================= > > > > To UNSUBSCRIBE your email address, click here: > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > > > > > > > ================================= > > > Help make your TechAssist database better! > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > ================================= > > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > ================================= > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ================================= > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > ================================= > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ================================= > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > ================================= Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ================================= To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe