I agree change the 120K resistor on the red CRT board should do it. al m wrote: > May be this will help, maybe you already tried this but,The smearing picture > is probably the resistors on the crt boards. Check the solder on the > daughter board for cracks for the no video problem. > Al Marquardt > ampm@xxxxxxx > Al Marquardt Electronic Repair > 206 W Main > Girardville Pa. 17935 > ----- Original Message ----- > From: "Larry E" <videotech@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Thursday, June 23, 2005 12:50 PM > Subject: [TechAssist] Zenith Z52Z95D 9-1674 no video, red crt blurry/smeared > convergence issues > > > >>Hi Guys, This Z52Z95D has the 9-1674 sweep and 9-1690 converg boards, >>complaint was no video has sound, >>replaced the 9-1674 module, set came up fine, but video was not good, when >>the weather channel, CNN, etc. >>puts up letters there is a green haze around the letters, put up the >>customers cross hatch and the red & blue >>horizontal is missing (from top of screen to bottom) the green is there, >>all 3 colors are there vertically(left to right) >>pulled R3243 behind the horiz. heatsink the 110K and R3244 the 82K as this >>is a known failure for the horiz. >>convergence bars missing, they are both good out of circuit, looked into >>the lenses and the red video is smeared/ >>washed out looking, this does not show up on the screen?? sprayed R5102 >>with freeze mist and red crt went blank, >>sprayed same resistor on green crt board and green blanked out, I did not >>have 110K 1/2 watts with me so couldn`t >>change them, before I could go out there today and replace them the >>customer called and said the set has >>again failed with same problem, no video has sound, he shuts off set for >>1/2 hour and set runs normally for 45 minutes >>then loses video again. This is the third time in 1 month that I have had >>similiar symptoms with the 1674/1690 >>combination of boards, convergence goes out, replace the 1690, set runs 24 >>hours and convergence fails again, >>or no video/dead set, replace 1674 set runs for 1-2 days and repeats the >>failure, if I replace both boards at the >>same time I`m not getting the re-call, this is killing my bottom line with >>all these freebie return calls, is anyone else >>running into this scenario?? Ed at Tri-State Module says Sears will now >>only change them as a pair, too many >>recalls, any ideas? Sorry for the long post, I have 2 customers waiting on >>me to "fix their set" Larry E >>Larry Eastman >>American TV & Electronics >>Crystal River, Fl. 34428 >> >>----------------------------------------------------------------------------- >>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm >>Set Vacation >>mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation >>Lost Password: http://www.tech-assist.org and select "Login Problems?". >>Email Archives: //www.freelists.org/archives/techassist/ >> >> > > > > ----------------------------------------------------------------------------- > This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ > -- ***************************** Bill Grabowski Triangle Appliance Kenosha,Wi 53142 262-694-6500 262-694-6523 fax bgrabowski@xxxxxxxxx ***************************** ----------------------------------------------------------------------------- This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/