[TechAssist] Re: Zenith (Unknown model) Picture to wide 9-1270
- From: "Gemini Computer & TV" <geminitv@xxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 02 Jun 2005 17:51:39 -0400
---------------------------------------------------------------
Text pasted from WinSTIPS 2.0
http://www.ServiceSoftware.com
---------------------------------------------------------------
ZENITH 9-1270
Excessive Width
Consumer Service
Qx3201 Pin Xstr
---------------------------------------------------------------
ZENITH 9-1270
Horizontal Deflection Intermittent
Jeff Stielau : 7/9/01 : Shoreline Electronics
Cracked/Burnt Solder Connection On Coil Lx3202. Located On Back Right Corner
Of Sweep Pc Board
---------------------------------------------------------------
ZENITH 9-1270
Horizontal Deflection Intermittent
Cracked/Burnt Solder Connection On Coil Lx3202. Located On Back Right Corner
Of Sweep Pc Board
---------------------------------------------------------------
ZENITH 9-1270
Picture Too Wide
Lx3201 Open
---------------------------------------------------------------
ZENITH 9-1270
Pincushion/ Bad Side Pincushion
Phil Hull
Found Lx 3201 Discolored Part # 20-4284-09 And Qx 3201 Shorted Part #
121-1187
---------------------------------------------------------------
ZENITH 9-1270
Width - Sides Streched Out
Simpson'S Tv
Lx262 Open And Qx3201
---------------------------------------------------------------
ZENITH 9-1270
Width Is Too Wide
Qx3201 Shorted
---------------------------------------------------------------
Bob Waterman, CET® #RI-28
Master Technician License #9109
Service Manager / Parts Manager
Gemini Computer, TV, & Security Alarms
(508)695-7302
(508)695-7769 FAX
geminitv@xxxxxxxxxxx
----- Original Message -----
From: "Scott Beebe" <Scott@xxxxxxxxxxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Wednesday, June 01, 2005 1:11 PM
Subject: [TechAssist] Zenith (Unknown model) Picture to wide 9-1270
Hello,
I have a 36" Zenith TV here with no tag on the back. The unit has a wide
picture, and adjusting the HSIZE pot has no effect. From working on some
zenith's in the past, I remembered a coil (LX3201) opens, and can cause that
problem. I then proceeded to replaced
LX3201, QX3201, CR3201, and IC3200, with no difference. The unit has the
9-1270 SMPS/SWEEP module, or 9-1428 main module. (From sticker inside case)
Any advice? TIA
Thanx,
Scott Beebe
Ohm Electronics Inc.
609 W. Clinton St.
Ithaca NY 14850
Voice: (607) 273-8406
Fax: (607) 273-8743
WWW.OhmElectronicsInc.com
mailto:Scott@xxxxxxxxxxxxxxxxxxxxx
----------------------------------------------------------------------------
-
This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
Lost Password: http://www.tech-assist.org and select "Login Problems?".
Appliance Repair List:
http://www.tech-assist.org/secure/tip/chatjoin.htm#app
Email Archives: //www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
Lost Password: http://www.tech-assist.org and select "Login Problems?".
Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app
Email Archives: //www.freelists.org/archives/techassist/
Other related posts:
