[TechAssist] Re: Zenith SE3191H Vertical problem. FIXED
- From: "Shaun" <satguy@xxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Wed, 16 Jun 2004 16:29:01 -0600
I finally found the problem on this set it was C2103 (16 volt 10 MFD) cap on
the 9-700 module. Thanks for everyone's help especially Bob at Bob's TV.
Shaun
Advanced Electronics
224 West Riverview Ave.
Fort Morgan, CO 80701
----- Original Message -----
From: "Intrepid Video Support" <support@xxxxxxxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Tuesday, June 08, 2004 8:56 PM
Subject: [TechAssist] Re: Zenith SE3191H Vertical problem.
> Shaun,
> Do you have an ESR meter? If not, the time you waste checking, replacing,
you could save with an ESR
> meter.
> I use the Dick Smith, kit for less than $50. I got mine over 6 years ago
and it's still going strong. I
> can check all the caps in a vertical circuit in just a few seconds...I
know this doesn't help you now, but
> it's something you should consider.
> Jeff
> --
> Intrepid Video TV/VCR Repair
> 263 S Front St, Steelton PA 17113
> 717-939-7708; (F) 717-564-4952
> www.intrepid-video.com www.tech-repair.net
> ----- Original Message -----
> From: "Shaun" <satguy@xxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, June 08, 2004 6:06 PM
> Subject: [TechAssist] Re: Zenith SE3191H Vertical problem.
>
>
> Is that supposed to be C2104 if so I have replaced both of those you
> mentioned. I need to know which one's are on the 700 module that need to
be
> checked or replaced. thanks.
>
> Shaun
>
> Advanced Electronics
> 224 West Riverview Ave.
> Fort Morgan, CO 80701
> ----- Original Message -----
> From: "Bob@Bobs tv" <woodman1@xxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, June 08, 2004 3:08 PM
> Subject: [TechAssist] Re: Zenith SE3191H Vertical problem.
>
>
> > Shawn,
> > Just saw your post, looking thru the training manual.. Code 4
> Vert
> > top 000/254 Code5 Vert height 000/254 Code6 Vert lin 000/254 Code7
> Vert
> > symmetry 000/254.. Tomorrow morning I will try to find the print, if you
> > need more help.. Make sure you replaced CX2110 and C2184 on the 9-605
> > module..
> > Bob,
> >
> > Bobs TV Worcester, ma
> >
> > woodman1@xxxxxxxx
> >
> > Main 508-853-1482
> > Fax 508-853-1480
> > ----- Original Message -----
> > From: "Shaun" <satguy@xxxxxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Tuesday, June 08, 2004 4:42 PM
> > Subject: [TechAssist] Re: Zenith SE3191H Vertical problem.
> >
> >
> > > I turned the vertical all the way up and still not enough. Where is
the
> > best
> > > place to check on the 26 volt supply as I have no schematic.
> > >
> > > Shaun
> > >
> > > Advanced Electronics
> > > 224 West Riverview Ave.
> > > Fort Morgan, CO 80701
> > > ----- Original Message -----
> > > From: "Phil Bader" <tjanphyl@xxxxxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Tuesday, June 08, 2004 1:05 PM
> > > Subject: [TechAssist] Re: Zenith SE3191H Vertical problem.
> > >
> > >
> > > > Shaun, don't over analyze.
> > > > If bumping up the value fills the screen, go for it.
> > > > That's probably just an average value.
> > > > phil Bader
> > > >
> > > > Shaun wrote:
> > > >
> > > > >This set has the 9-700 digital module, 9-605-03 and 9-604-02.
Problem
> > is
> > > the
> > > > >vertical looks like it needs to be adjusted to make a full picture,
> but
> > > the
> > > > >adjustment is at 221 in the service menu which should be close for
a
> > full
> > > > >picture. I have checked or replace all the caps on the 9-605-03
along
> > > with
> > > > >several others on the 9-604-02. Anyone have any old notes on this
> > beast?
> > > > >
> > > > >Shaun
> > > > >
> > > > >Advanced Electronics
> > > > >224 West Riverview Ave.
> > > > >Fort Morgan, CO 80701
> > > > >
> > > > >
> > > >
> > >
> >
>
>---------------------------------------------------------------------------
> > > --
> > > > >Lost Password:
> > > > >http://www.tech-assist.org and select "Login Problems?".
> > > > >Email Archives:
> > > > >//www.freelists.org/archives/techassist/
> > > > >
> > > > >
> > > > >
> > > >
> > > > --
> > > >
> > > > Philip Bader
> > > > Jan Phyl TV Inc. (estab. 1976)
> > > > 3420 Recker Hwy. Winter Haven, Fl. 33880
> > > > Fax (863) 299-8821
> > > > email: tjanphyl@xxxxxxxxxxxxxxx
> > > >
> > > >
> > > >
> > >
> >
>
> --------------------------------------------------------------------------
> > > ---
> > > > Lost Password:
> > > > http://www.tech-assist.org and select "Login Problems?".
> > > > Email Archives:
> > > > //www.freelists.org/archives/techassist/
> > >
> > >
> >
>
> --------------------------------------------------------------------------
> > ---
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> >
> >
> >
>
> --------------------------------------------------------------------------
> ---
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
- » [TechAssist] Re: Zenith SE3191H Vertical problem. FIXED
