Why would removing the yoke disable the HV,removing it (yoke) changes the "tuning" of the overall circuit but will not kill the HV. The only exception is were there is a B+ jumper on the yoke plug. Country TV Ron Miller Inez, TX. 77968 ----- Original Message ----- From: "Tel-Tek" <teltek3@xxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Sunday, October 31, 2004 9:57 AM Subject: [TechAssist] Re: Symphonic shut down > Just can't figure out the Yoke part, since this > would also eliminate all of the Horizontal Output > section. > Would also disable your HV, if the yoke was unplugged. > New one on me. > > -Ed- > Ed Gaidies > Tel-Tek Electronics > Ontario-Canada > > teltek3@xxxxxxxxxxxx > teltek@xxxxxxxxx > > Intrepid Video Support wrote: > > Set I had wouldn't start unless the yoke and CRT board were removed. > > I called Funai, they suggested bad CRT. > > I already replaced the FLY on mine. > > Jeff > > -- > > Intrepid Video TV/VCR Repair > > 263 S Front St, Steelton PA 17113 > > 717-939-7708; (F) 717-564-4952 > > www.intrepid-video.com www.tech-repair.net > > ----- Original Message ----- > > From: "Tel-Tek" <teltek3@xxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Sunday, October 31, 2004 10:37 AM > > Subject: [TechAssist] Re: Symphonic shut down > > > > > > Jeff; > > Why remove yoke? > > > > -Ed- > > Ed Gaidies > > Tel-Tek Electronics > > Ontario-Canada > > > > teltek3@xxxxxxxxxxxx > > teltek@xxxxxxxxx > > > > Intrepid Video Support wrote: > > > >>Perry, > >>If this is a 2002 set, suspect bad CRT. > >>Remove yoke and CRT pcb, if set fires up, bad CRT. > >>Jeff > >>-- > >>Intrepid Video TV/VCR Repair > >>263 S Front St, Steelton PA 17113 > >>717-939-7708; (F) 717-564-4952 > >>www.intrepid-video.com www.tech-repair.net > >>----- Original Message ----- > >>From: "Perry Thorpe" <pkthorpe@xxxxxxxxx> > >>To: "techassist" <techassist@xxxxxxxxxxxxx> > >>Sent: Saturday, October 30, 2004 11:34 AM > >>Subject: [TechAssist] Symphonic shut down > >> > >> > >>I have a Symphonic Model# WF-13,IT goes in to shut down so fast I can't check it. I think it may voltage > >>Reg. problem the short time it is on I get about 114vdc reg voltage,Horiz. output wave form looks > > > > good,reg > > > >>input ckt voltage is 157vdc the goes to low 150's to high 140's vdc at power up ,I don't have a manual > >>hate to order one its just a 19" that belonges to a friend. H.O. is a D2627 reg. is a K2662. If that > >>helps. > >>Any and all help on this one I would be greatly thankful. > >> > >>Perry > >>Thorpe's Electronics > >>Beattyville,KY 41311 > >>pkthorpe@xxxxxxxxx > >> > >> > >> > >>-------------------------------------------------------------------------- --- > >>Lost Password: > >>http://www.tech-assist.org and select "Login Problems?". > >>Email Archives: > >>//www.freelists.org/archives/techassist/ > >> > >> > >> > >>-------------------------------------------------------------------------- --- > >>Lost Password: > >>http://www.tech-assist.org and select "Login Problems?". > >>Email Archives: > >>//www.freelists.org/archives/techassist/ > >> > > > > > > -------------------------------------------------------------------------- --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > > > -------------------------------------------------------------------------- --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/