Nope....found the fix on your CD......D707 Reel-Sensor. - Ed - Ed Gaidies TEL-TEK ELECTRONICS Midland, Ontario, Canada. teltek2@xxxxxxxxxxxx teltek@xxxxxxx > From: "Tech Repair CD support" <support@xxxxxxxxxxxxxxx> > Reply-To: techassist@xxxxxxxxxxxxx > Date: Wed, 22 May 2002 16:52:27 -0400 > To: <techassist@xxxxxxxxxxxxx> > Subject: [TechAssist] Re: Sharp VCR VC-H903U > > > Ed, > Are these symptoms with a test jig? > If so, try a real cassette. > Jeff > FAX 717-564-4952 > Intrepid Video & Electronics > 501 Luther Rd > Harrisburg PA 17111-2055 > Be careful of your thoughts. > They may become your words any moment. > Order your tip CD today. Filled with TV, VCR, camcorder tips and more. > Version 3.0, ready, with more tips, user friendly program. > $49.00 for CD, plus first year of tip updates. > sales@xxxxxxxxxxxxxxx for more info > www.tech-repair.net www.intrepid-video.com > www.thetoolcaddy.com www.9-11-2001tragedy.com > ----- Original Message ----- > From: "Tel-Tek Electronics" <teltek2@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Wednesday, May 22, 2002 1:59 PM > Subject: [TechAssist] Re: Sharp VCR VC-H903U > > >> >> Thanks Gary; >> Nope...I really think this is not a mechanical problem. The micro is getting >> a wrong signal from somewhere. Since the tape end sensors are in the basket, >> I changed it, to no avail. This fault goes like someone had hit the stop >> button, same with FF and rewind, all seem actions that are predetermined. >> BTW....before you go for a new motor assy on that other one, send me a >> picture of the motor, I'm reasonably sure I have one on the junk pile. >> >> -Ed- >> Tel-Tek Electronics >> Midland, Ont. Canada. >> teltek2@xxxxxxxxxxxx >> >> "Quality will be remembered, long after Price is forgotten" >> ----- Original Message ----- >> From: "Gary McCartney" <number63@xxxxxxxxxxxxx> >> To: <techassist@xxxxxxxxxxxxx> >> Sent: Wednesday, May 22, 2002 1:06 PM >> Subject: [TechAssist] Re: Sharp VCR VC-H903U >> >> >>> >>> Ed, I recently did a Sharp VCR, model VC-H992U. The problem was not >>> exactly the same as yours but I thought I'd mention it in case it solves >>> yours also. >>> >>> This VCR, when cue and review was used during play, would growl and then >>> shut off, plus eject would work in this state. I had to unplug the VCR >>> for a while to get it to reset itself. >>> >>> The solution was the tiny nylon drive coupler on the loading motor shaft >>> had split, causing the motor shaft to just spin when the mechanism was >>> under a lot of torque. I roughed up the motor shaft a bit and used JB >>> Weld to fasten the nylon drive coupler permanenty onto the shaft. The >>> unit belongs to a relative, so I won't worry if the weld job doesn't >>> hold, I'll order them a new motor assembly. >>> >>> >>> >>> Gary McCartney >>> >>> McCartney Electronics >>> 7134 Fife Rd, RR 7 >>> Guelph Ontario Canada N1H 6J4 >>> Fax: (519)821-1530 >>> email: number63@xxxxxxxxxxxxx >>> >>> >>> >>> >>> >>> Tel-Tek Electronics <teltek2@xxxxxxxxxxxx> wrote: >>>> >>>> Model VC-H903U >>>> >>>> Unit will go into Play for about 4 to 5 seconds, then stop. >>>> Automatically goes to Rewind for about 4 seconds, then goes to Fast >> Forward >>>> for 4 seconds, and then stops. >>>> Unit will remain powered up, but repeats the same cycle each time the >> Play >>>> is pushed. >>>> When F/F or Rewind is pushed, will run the same amount of time >> (4seconds) >>>> then stop. >>>> Have replaced the basket from a junker, have cleaned the mode switch and >>>> checked alignment of mode switch. >>>> Anybody had these "woes" >>>> >>>> TIA. >>>> >>>> -Ed- >>>> Tel-Tek Electronics >>>> Midland, Ont. Canada. >>>> teltek2@xxxxxxxxxxxx >>>> >>>> "Quality will be remembered, long after Price is forgotten" >>>> >>>> ------------------------------------------ >>>> To REMOVE your email address, click here: >>>> http://www.tech-assist.org/unsubb.html >>>> To CHANGE your email address, click here: >>>> http://www.tech-assist.org/change.html >>>> ------------------------------------------ >>>> ***NEW*** Tips Added Instantly!!!*** >>>> Submit Repair Tips here: >>>> http://www.tech-assist.org/secure/tip/ >>> >>> -- >>> >>> >>> >>> Gary McCartney >>> >>> McCartney Electronics >>> 7134 Fife Rd, RR 7 >>> Guelph Ontario Canada N1H 6J4 >>> Fax: (519)821-1530 >>> email: number63@xxxxxxxxxxxxx >>> ------------------------------------------ >>> To REMOVE your email address, click here: >>> http://www.tech-assist.org/unsubb.html >>> To CHANGE your email address, click here: >>> http://www.tech-assist.org/change.html >>> ------------------------------------------ >>> ***NEW*** Tips Added Instantly!!!*** >>> Submit Repair Tips here: >>> http://www.tech-assist.org/secure/tip/ >> >> ------------------------------------------ >> To REMOVE your email address, click here: >> http://www.tech-assist.org/unsubb.html >> To CHANGE your email address, click here: >> http://www.tech-assist.org/change.html >> ------------------------------------------ >> ***NEW*** Tips Added Instantly!!!*** >> Submit Repair Tips here: >> http://www.tech-assist.org/secure/tip/ >> > > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.tech-assist.org/change.html > ------------------------------------------ > ***NEW*** Tips Added Instantly!!!*** > Submit Repair Tips here: > http://www.tech-assist.org/secure/tip/ ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.tech-assist.org/change.html ------------------------------------------ ***NEW*** Tips Added Instantly!!!*** Submit Repair Tips here: http://www.tech-assist.org/secure/tip/