Kevin, From Tech Repair CD: RCA \PTK195\Dead* Fuse Ok (EEPROM RESET)\\\PTK195\All Voltages Looked Ok In Power Supply. Found That The EEPROM Glitched. Unsoldered Pin 8 Of EEPROM* Plugged In Set* Held Power Button* And Shorted Pin 8 To Its' Run.\Set Woke Up And EEPROM Returned To Normal\\\\\\\ RCA\PTK195MT\Dead set* will not try to turn on.\\\PTK195MT\Checking micro* u13101* found it would read the EEPROM at plug in. After that pin 5 would pulse from 2.5 to 5 volts. Pin 19 stays at 0 volts.\Found pin 31* filter cpu at .6 volts* should be 1.7 volts. Ohms check read 2.5k. Lifted c13312 and set came up and ran. Replace c13312 off pin 31 of u13101\\\\\\\ RCA\PTK195MT\Dead. Had only 2.4 volts on pin 36 of u13101\\\PTK195MT\Removed flux from circuit board and pin 36 came up to 4.7 volts\\\\\\\\ RCA\PTK195MT\Dead Set U13101 pins 6*7 & 8 at 5 VDC But the voltage at pin 5 was 0 VDC\\\PTK195MT\checked all the supplies and they were all right. Q13501-c was 3VDC and Q13503-B was at .6 VDC. We found C13504 leaky.\Replaced C13504 and the reset worked. U13101-5 was back to 2VDC. Replaced c13504.\\\\\\\ RCA\PTK195MT\Dead* No Attempt To Start; VCC at U13101 Normal* But Standby Clock & Data Pulsating* As Well As 150V(110V-140V) & 16V(12V-16V) Sources\\\PTK195MT\Checking Around U14101* Pin 6 Was Pulsating From 8-12V And Pin 2 Was At 7V. We Found That The Run Diode CR14111*\Which Is A Surface-Mount Device* Was Missing From The Chassis. Replaced The Diode & Restored Normal Operation. Installed missing cr14111\\\\\\\ RCA\PTK195MT\Dead set* would not pulse at turn on.\\\PTK195MT\Found pin 4 of u13101 (run data) low at turn on. By lifting jumper jc12106 the set would come up in the service mode.\ Found the trace from jc12106 ran under jumper jc12114. By lifting this jumper the set came up and ran. Cleaned glue under this jumper to repair the set.\Jc12114 is in the audio circuit* off pins 2 and 6 of u11401. Clean glue from jumper jc12114\\\\\\ Jeff Dougherty Intrepid Video TV/VCR 263 S Front St Steelton PA 17113 fax...717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "Kevin" <kevintv@xxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, January 15, 2004 2:44 PM Subject: [TechAssist] Re: RCA PTK-195, dead. Eeprom has 2.8 volts at pins 5 and 8. Pin 6, the clock line has 0.04 volts on it. I'm pretty sure the eeprom is my fault, but what is causing the clock line to be so low? And what kills the eeprom in the 195 chassis? Bad grounds? TIA Kevin Wilks Kevin's TV & Video Repair Penticton BC Canada kevintv@xxxxxxx -----Original Message----- From: techassist-bounce@xxxxxxxxxxxxx [mailto:techassist-bounce@xxxxxxxxxxxxx] On Behalf Of support@xxxxxxxxxxxxxxxxxx Sent: Thursday, January 15, 2004 9:53 AM To: techassist@xxxxxxxxxxxxx Subject: [TechAssist] Re: RCA PTK-195, dead. Based on the information you provided, could be one of 20 or more possibilities.. Jeff Dougherty Intrepid Video TV/VCR 263 S Front St Steelton PA 17113 fax...717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "Kevin" <kevintv@xxxxxxx> To: "TECH-ASSIST" <techassist@xxxxxxxxxxxxx> Sent: Wednesday, January 14, 2004 11:38 PM Subject: [TechAssist] RCA PTK-195, dead. This RCA PTK195 PROJO does not power up. When I plug the set in I hear the typical RCA P/S "tweak" of the horizontal frequency. All fuses are good--no obvious faults. What are the typical problems with these sets? TIA Kevin Wilks Kevin's TV & Video Repair Penticton BC Canada kevintv@xxxxxxx ----------------------------------------------------------------------------- Jokes, complaints, off topics, general chat. Everything other than repair help problems can be found at this new list. No archives and posts will not be found on Google or any other engine!To remove or join, email chat-request@xxxxxxxxxxxxxxx with remove or join as the subject. Send to the list at chat@xxxxxxxxxxxxxxx once subscribed. ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/