Wow! Damon.... Where do you buy your parts? I have not found anything for that price nor have I found anyone that has i= t in stock. Most are from $90 to $110 and I have to send it in with a 2 to 4 week turn = around. Daryl Daryl's TV 2402 Wyoming Ave. El Paso, TX 79903 915-565-9184 Voice/Fax daryls_tv@xxxxxxx www.angelfire.com/tv2/daryls_tv ----- Original Message ----- From: Damon <damoneb@xxxxxxxxxxx> To: techassist@xxxxxxxxxxxxx Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power supply prob= lem Date: Tue, 26 Jul 2005 07:54:59 -0500 >=20 > Daryl, > 264104 is $58.95 and $20 Dud. > How many hours you got into that power supply? >=20 > Damon B > Telrad Electronics > Fort Wayne IN > ----- Original Message ----- > From: <daryls_tv@xxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Monday, July 25, 2005 12:19 PM > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power supply > problem >=20 >=20 > > Jerry, > > You are absolutely correct. > > I used a second meter and I did get resistance. Whether it is the right > re=3D > > adings.....???? > > Thanks for the tip. > > Daryl > > Daryl's TV > > 2402 Wyoming Ave. > > El Paso, TX 79903 > > 915-565-9184 Voice/Fax > > daryls_tv@xxxxxxx > > www.angelfire.com/tv2/daryls_tv > > > > ----- Original Message ----- > > From: "J Silverman" <greentron@xxxxxxx> > > To: techassist@xxxxxxxxxxxxx > > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power supply > prob=3D > > lem > > Date: Sat, 23 Jul 2005 14:28:31 -0400 > > > > >=3D20 > > > That sound normal to me! If you put some current into pins 1 and 2, s= ay > f=3D > > rom > > > an ohm meter, then you should see some ohms appear at terminals 3 and= 4, > =3D > > if > > > your meters have the right polarity. > > > Jerry Silverman > > > Greentron Inc > > > 4 Newland Ave > > > Greenville SC 29609 > > > Fax/Phone 864 232 3889 > > > mail to: greentron@xxxxxxx > > > ----- Original Message ----- > > > From: <daryls_tv@xxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Saturday, July 23, 2005 1:20 AM > > > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power supply > > > problem > > >=3D20 > > >=3D20 > > > > No... I don't have any schematics on this set. > > > > I think I may have found the problem. I have absolutly no resistan= ce > > > readi=3D3D > > > > ngs between pins 3 & 4 of the opt-coupler, even on high meg scale. > > > > I will post the results when the part comes in. > > > > Thanks, > > > > Daryl > > > > Daryl's TV > > > > 2402 Wyoming Ave. > > > > El Paso, TX 79903 > > > > 915-565-9184 Voice/Fax > > > > daryls_tv@xxxxxxx > > > > www.angelfire.com/tv2/daryls_tv > > > > > > > > ----- Original Message ----- > > > > From: Damon <damoneb@xxxxxxxxxxx> > > > > To: techassist@xxxxxxxxxxxxx > > > > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power sup= ply > > > prob=3D3D > > > > lem > > > > Date: Fri, 22 Jul 2005 22:20:41 -0500 > > > > > > > > >=3D3D20 > > > > > Do you have schematics? If so, one of the transistors driving or > being > > > > > driven by the optoisolator can be jumpered (screwdriver) and maybe > the > > > un=3D3D > > > > it > > > > > will start, I'm pretty sure that if that's the case, replacement = of > t=3D > > he > > > > > board will save you some time/money. > > > > >=3D3D20 > > > > > Damon B > > > > > Telrad Electronics > > > > > Fort Wayne IN > > > > > ----- Original Message ----- > > > > > From: <daryls_tv@xxxxxxx> > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > Sent: Friday, July 22, 2005 1:10 PM > > > > > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power > supply > > > > > problem > > > > >=3D3D20 > > > > >=3D3D20 > > > > > > After re-checking the power supply, I discovered that the chopp= er > is > > > not > > > > > os=3D3D3D > > > > > > cillating. I guess I was in a hurry and used the wrong ground = as > > > > > reference. > > > > > > I rechecked every component on the primary side and still not > findi=3D > > ng > > > > > anyth=3D3D3D > > > > > > ing bad. > > > > > > I thought I would sub another chopper into it but I couldn't fi= nd > a=3D > > ny > > > > > cross=3D3D3D > > > > > > for it. I hate to order one and wait several days only find o= ut > t=3D > > hat > > > =3D3D > > > > may > > > > > =3D3D3D > > > > > > not be it. > > > > > > Daryl=3D3D3D20 > > > > > > Daryl's TV > > > > > > 2402 Wyoming Ave. > > > > > > El Paso, TX 79903 > > > > > > 915-565-9184 Voice/Fax > > > > > > daryls_tv@xxxxxxx > > > > > > www.angelfire.com/tv2/daryls_tv > > > > > > > > > > > > > > > > > > ----- Original Message ----- > > > > > > From: Damon <damoneb@xxxxxxxxxxx> > > > > > > To: techassist@xxxxxxxxxxxxx > > > > > > Subject: [TechAssist] Re: RCA D52W20, ITC222, Convergence power > sup=3D > > ply > > > > > prob=3D3D3D > > > > > > lem > > > > > > Date: Fri, 22 Jul 2005 08:00:20 -0500 > > > > > > > > > > > > >=3D3D3D20 > > > > > > > Daryl, > > > > > > > I have yet to see a defective convergence power supply on the > ITC > > > 222, > > > > > > > HOWEVER..... > > > > > > > The CTC 195/197 series has had intermittant conv power shutdo= wn, > =3D > > and > > > =3D3D > > > > the > > > > > > > board cost was cheap enough to just replace it entirely. It > might=3D > > be > > > =3D3D > > > > the > > > > > =3D3D3D > > > > > > way > > > > > > > to go on this unit. > > > > > > >=3D3D3D20 > > > > > > > On the boards I worked on, I was able to eventually see it fa= il, > > > then=3D3D > > > > by > > > > > > > jumpering two leads on the primary side I was able to restart > it > > > and > > > > > ver=3D3D3D > > > > > > ify > > > > > > > it was the smps, and it was not a "shorting" type of failure. > The > > > > > oscilla=3D3D3D > > > > > > tor > > > > > > > just quits oscillating for no good reason. But in your case > > > oscillati=3D3D > > > > on > > > > > > > isn't the issue, tranferring power to the secondary is......d= oes > =3D > > the > > > > > final > > > > > > > output drive the transformer at all? > > > > > > >=3D3D3D20 > > > > > > > Damon B > > > > > > > Telrad Electronics > > > > > > > Fort Wayne IN > > > > > > > ----- Original Message ----- > > > > > > > From: <daryls_tv@xxxxxxx> > > > > > > > To: <TechAssist@xxxxxxxxxxxxx> > > > > > > > Sent: Thursday, July 21, 2005 6:18 PM > > > > > > > Subject: [TechAssist] RCA D52W20, ITC222, Convergence power > supply > > > > > problem > > > > > > >=3D3D3D20 > > > > > > >=3D3D3D20 > > > > > > > > RCA D52W20, ITC222, Convergence power supply problem > > > > > > > > > > > > > > > > Another looser here. > > > > > > > > Customer claims they changed channels and lost the > convergence. > > > > > > > > What I found is no control of convergence and a distorted > pictu=3D > > re. > > > > > > > > There are no voltages out of the convergence power supply on > the > > > > > > > secondarie=3D3D3D3D > > > > > > > > s. > > > > > > > > I do have power on the primary of the smps and does appear = to > be > > > > > > > oscillatin=3D3D3D3D > > > > > > > > g. > > > > > > > > I checked all of the semi's, resistors and electro's. I ohm= ed > o=3D > > ut > > > t=3D3D > > > > he > > > > > > > switc=3D3D3D3D > > > > > > > > h mode power transformer. I didn't find any bad components. > > > > > > > > I hope someone has encountered this before and can give a f= ew > > > > > pointers. > > > > > > > > Thanks, > > > > > > > > Daryl >=20 >=20 > -------------------------------------------------------------------------= ---- > This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=3Dset%20techassist%20va= cation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ --=20 ___________________________________________________________ Sign-up for Ads Free at Mail.com http://promo.mail.com/adsfreejump.htm ----------------------------------------------------------------------------- This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/