Clean or replace the running voltage control. You may have also to replace the 2.2mf, 15mf, and 39/47mf from pin 16 to the base of the shopper transistor. With the set off check for 138-140v B+ at flyback txmer, and 12.8 at CR1118. (Running 143-44 and 13.6-.9) Good luck, pete Perdomo TV, INc Miami Fl. Sender: techassist-bounce@xxxxxxxxxxxxx From: support@xxxxxxxxxxxxxxxxxx(Intrepid=A0Video=A0Support) Date: Fri, Oct 1, 2004, 11:08pm To: techassist@xxxxxxxxxxxxx Subject: [TechAssist] Re: Proscan CTC169 Reply=A0to: techassist@xxxxxxxxxxxxx Mine is the bleeder assembly..at least I think so. If I remove the wire from the CRT that goes to the bleeder assembly, the set starts with high voltage. Jeff -- Intrepid Video TV/VCR Repair 263 S Front St, Steelton PA 17113 717-939-7708; (F) 717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "tvservice" <tvservice@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, October 01, 2004 9:37 AM Subject: [TechAssist] Re: Proscan CTC169 Flyback! Fixed 2 this week same symptom 1 directview 1 projo Robert tvservice@xxxxxxxxxxxxx H & H Electronics Inc ----- Original Message ----- From: "Intrepid Video Support" <support@xxxxxxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, September 30, 2004 8:24 PM Subject: [TechAssist] Re: Proscan CTC169 Russ.. I have the same set here. You should include the model number and full chassis as there are different variations of this chassis. What happens to collector voltage and standby and B+ when you press power? Do you have secondary voltages on the FLY? I have none, but when I press power, 26 v starts up, 15V goes down and B+ goes down..like they're being held down at power on. Jeff -- Intrepid Video TV/VCR Repair 263 S Front St, Steelton PA 17113 717-939-7708; (F) 717-564-4952 www.intrepid-video.com www.tech-repair.net ----- Original Message ----- From: "Hoyt's TV" <hoytstv@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, September 30, 2004 10:37 AM Subject: [TechAssist] Proscan CTC169 Direct view CTC169 Power supply is not firing up. I cannot find any shorts or heavy loads on the output side. I've tried watching it on a scope and bringing the AC up slowly, not even a twitch. Has raw B+. I haven't had many CTC169s, does anyone know of any common failures in this supply? Looks like a thousand or more tips in the tip section, will take me a month just to sort through them. Thanks Russ Hoyt Hoyt's TV Exeter, NH ---------------------------------------------- --- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ---------------------------------------------- --- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ---------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ---------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/