May be a slightly different chassis, but I just had a DPTV335 that would shutdown. I went in circles until I noticed that the CRT DAG cable from the LSM to one of the CRTs was missing. I connects to a lug close to the HV Transformer and any of the spring lugs on any of the CRTs. Corey Brazell Audio Video Electronics 12169 SC Hwy 121 Newberry SC 29108 > [Original Message] > From: Gemini Computer & TV <geminitv@xxxxxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Date: 12/5/2003 7:04:46 AM > Subject: [TechAssist] Re: Philips 50PP920217, chas DPTV305, shuts down after 20 seconds > > How about this? > > Symptom: > No Power/Shutdown. > > Cause: > Possible defective resistor. > > Resolution: > Check resistor 3306 15 ohm surface mount off the gate of FET 7301 on the > large signal board. If found defective replace with part number 3198 021 > 51590. > > Applies To: > 43PP920201, 43PP920217, 43PP920217F, 43PP920284, 43PP920284F, 46PP930201, > 46PP930217, 46PP930217F, 46PP930284, 46PP930284F, 50PP920201, 50PP920217, > 50PP920217F, 50PP920284, 50PP920284F, 51PW930317F, 51PW936317F, 55PP935201, > 55PP935217, 55PP950201, 55PP950217, 55PP950284, 55PW936317F, 55PW938317F, > 60PP920201, 60PP920217, 60PP920217F, 60PP935201, 60PP935217, 60PP950201, > 60PP950217, 60PW936317F, 60PW938317F, DPTV305, DPTV305F, DPTV310, DPTV315, > DPTV330, DPTV330F, DPTV335, DPTV340 > > Bob Waterman, CET® #RI-28 > Master Technician License #9109 > Service Manager / Parts Manager > Gemini Computer, TV, & Security Alarms > (508)695-7302 > (508)695-7769 FAX > geminitv@xxxxxxxxxxxxxxxx > geminitv@xxxxxxx > www.geminicomputertvsecurityalarms.com > > > ----- Original Message ----- > From: "Jim Myers" <jr.myers@xxxxxxxxxxx> > To: "TechAssist" <techassist@xxxxxxxxxxxxx> > Sent: Thursday, December 04, 2003 12:09 PM > Subject: [TechAssist] Philips 50PP920217, chas DPTV305, shuts down after 20 > seconds > > > > No raster appears but if I disconnect a cable from the HOP board to a CRT > > board then a slick raster of the disconnected color shows just prior to > > shutdown. All voltages check ok including the 130V. The SSB, SSM and HOP > > have been replaced. Any tips or is there some way to defeat the shutdown > to > > aid in troubleshooting? I have the Force manual. > > Thanks, > > ************************************************** > > Jim Myers > > Since 1972 > > Telrad Electronic Services Co. > > Fort Wayne, IN 46815 > > ************************************************* > > > > > **************************************************************************** > * > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > **************************************************************************** * > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ ***************************************************************************** Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/