It must be obvious when the Lamps are bad then. By that I mean,you must be able to visibly tell that the Lamp has gone bad....... this one is not(visibly). At over $250 a piece,I'd like to have a way to Verify that the Lamp is bad. I would hate to order one only to find a Bad connection is why it doesn't lite-up. Peggs At 12:46 PM 2/20/06, J Silverman wrote: >Its an arc lamp so it is not supposed to "measure". An interlock prevents >you from accessing the kilovolt arc strike and hundreds of high frequency AC >operating volts. The lamp life varies from one lamp type to another, but >4000 hours is probably a reasonable life to expect. The life is shortened by >frequent restarts. Panasonic had a ballast mod kit to reduce the strike >voltage, which was causing a reduction in lamp life, for certain models and >serial numbers. Some brands have no ballast problems but some brands have a >lot. One servicer that services a lot of LCD and DLP projectors says that >they always take a ballast along JIC. >Jerry Silverman >Greentron Inc >4 Newland Ave >Greenville SC 29609 >Fax/Phone 864 232 3889 >mail to: greentron@xxxxxxx >----- Original Message ----- >From: "peggs" <peggs@xxxxxxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: Monday, February 20, 2006 4:39 PM >Subject: [TechAssist] Panasonic LCD model PT-50LC13 > > > > My first large screen LCD TV Repair,so excuse the obvious questions. > > I've repaired a few Flat panel monitors,and one small 23" flat panel > > Televison,but this one is new ground for me. > > > > Customer is not happy...... he's replaced the Lamp himself once(a few days > > out of warranty), that one lasted about a year and his TV is not working > > again(same symptom). > > > > At Power On,Power Light goes from Red to Green momentarily,then to Orange > > with 2 quick blinks.....pause....2 quick blinks(and so on). > > Lamp measures open(that is by normal 'projector' bulb standards),that's my > > first question,How should these Lamps measure ??? > > But, I also have no Voltage on the Lamp's Connector........ which begs my > > 2nd question,What Voltage should I measure for the Lamp ??? > > > > Looks like a Lamp and Ballast(board) Repair(man,these things are > > expensive),but I thought I better get some input first. > > WinStips seems to agree,but in there I see a KIT (LSUC0022) for the >Ballast > > PCB Repair. > > Anybody installed one of these Kits ??? > > > > Peggs > > Peggs' Electronics > > 1519 West 2nd Street > > Owensboro,KY 42301 > > 270-926-4968 > > fax 270-686-7399 > > peggs@xxxxxxxxxxxxx > > > > -------------------------------------------------------------------------- >--- > > This Email List is accessible to the general public through search >engines. Remove: http://www.tech-assist.org/remove.htm > > Set Vacation >mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > > Lost Password: http://www.tech-assist.org and select "Login Problems?". > > Email Archives: //www.freelists.org/archives/techassist/ > >----------------------------------------------------------------------------- >This Email List is accessible to the general public through search >engines. Remove: http://www.tech-assist.org/remove.htm >Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation >Lost Password: http://www.tech-assist.org and select "Login Problems?". >Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/