[TechAssist] Re: Mitsubishi CS-3521R need partial print video or
- From: "Dave Routson" <davestv@xxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Tue, 30 Jul 2002 14:24:29 -0500
Thanks Bruce, you put me to checking for that IC and
it did have the M51366SP but my trouble is beyond
it. I could get video all the way to the video out jack
fine so trouble beyond IF chip. However I do have a
similar schematic but still not good enough. I did find
by calling Mitsubishi that the resistors that were overheated
went directly to a voltage regulator IC which it turns
out is a 12V regulator and was only outputting 8V to
video switching chips. So I figure this is were my trouble
is originating. Will update with complete cure if customer
approves go ahead since parts have to be ordered from
Mits.
Dave Routson
davestv@xxxxxxxxxxx
208 Stroud
Cleburne, TX 76033-8738
----- Original Message -----
From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Monday, July 29, 2002 11:03 AM
Subject: [TechAssist] Re: Mitsubishi CS-3521R need partial print video or
I have a print for a CK 3500 (M51366SP) IC 101 Video SIF. If it uses the
same chip can send a copy. This print is 2 ft by 3 ft, will send as needed.
If it is not similar just disregard Dave.
Bruce
B&T Electronics.
----- Original Message -----
From: "Dave Routson" <davestv@xxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Monday, July 29, 2002 11:12 AM
Subject: [TechAssist] Mitsubishi CS-3521R need partial print video or
>
> Wondering if anyone has a print of video luminance
> of Mit CS-3521R. I have what looks like a loss of
> luminance signal. I did the PIP bypass and the chroma
> signal is there but seem to be missing the lum signal and
> having difficult time trying to trace where the lum and
> chrom are processed. It also has a resistor that has
> overheated and may have changed value but cannot
> identify what it is. It is R8A2 and beside it an integrated
> circuit C7A8 looks like it was heated by the R8A2
> and may be damaged. Any help appreciated.
> Dave Routson
> davestv@xxxxxxxxxxx
> 208 Stroud
> Cleburne, TX 76033-8738
>
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.tech-assist.org/change.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.tech-assist.org/change.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.tech-assist.org/change.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
- References:
- [TechAssist] Mitsubishi CS-3521R need partial print video or
- From: Dave Routson
- [TechAssist] Re: Mitsubishi CS-3521R need partial print video or
- From: Bruce Tiedeman
Other related posts:
- » [TechAssist] Mitsubishi CS-3521R need partial print video or
- » [TechAssist] Re: Mitsubishi CS-3521R need partial print video or
- » [TechAssist] Re: Mitsubishi CS-3521R need partial print video or
- [TechAssist] Mitsubishi CS-3521R need partial print video or
- From: Dave Routson
- [TechAssist] Re: Mitsubishi CS-3521R need partial print video or
- From: Bruce Tiedeman