[TechAssist] Re: Magnavox PTV350 need resistor value

Terry, no problem, glad to help, Have a safe & prosperous New Year, Larry E

Terry J Hutchison wrote:

> Thanks for taking the time to help.  That resistor finished up the job.
> Happy New Year and thanks again.  Terry
>
> > [Original Message]
> > From: Phillip R. Hull <phil245@xxxxxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Date: 12/31/03 11:55:29 AM
> > Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
> >
> > R45 is 560 ohm 1/4 Watt    R41 is 7.5 K  1/4 Watt
> > Phillip R Hull     STET
> > phil245@xxxxxxxxxxxxx
> > FAX 517--569-3075
> > Professional Technicians only
> > ----- Original Message -----
> > From: "Terry J Hutchison" <sony1@xxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>; <techassist@xxxxxxxxxxxxx>
> > Sent: Wednesday, December 31, 2003 11:30 AM
> > Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
> >
> >
> > > Appreciate your time, this resistor is on the convergence wave form
> board,
> > > over half the components on this board only have two numbers this
> > > resistor(R45) is connected by trace path to JU2and R46 at one end the
> > other
> > > end looks like a ground and R41 goes to pin 13 of IC3. I just assume
> this
> > > module could be like a lot of RCA chasis and leave off the beginning
> > > numbers in some locations.  The only three digit markings on this module
> > > begin with 1 ie R190.  Hope this is enough and I really appreciate the
> > > help.  Terry
> > >
> > >
> > > > [Original Message]
> > > > From: Larry E. <videotech@xxxxxxxxxxxx>
> > > > To: <techassist@xxxxxxxxxxxxx>
> > > > Date: 12/31/03 10:36:36 AM
> > > > Subject: [TechAssist] Re: Magnavox PTV350 need resistor value
> > > >
> > > > Terry, According to NAP service manual all resistors are 3 digits,
> > > re-check number, if it is 2 digits
> > > > give me location, (tied to which parts) and I`ll check the schematic
> and
> > > try to find it for you, LarryE
> > > > Larry Eastman
> > > > American TV & Electronics
> > > > Crystal River, Fl. 34428
> > > >
> > > > Terry J Hutchison wrote:
> > > >
> > > > > Set came in with no filiment but had HV, replaced C455 restored
> > > filiment volts but have burned resistor on deflection  board need value
> > > cannot read it is R45. Thanks in advance for any help.  Terry
> > > > >
> > > > > Terry J Hutchison
> > > > > sony1@xxxxxxxx
> > > > > Why Wait? Move to EarthLink.
> > > > >
> > > > >
> > >
> >
> ****************************************************************************
> > > *
> > > > > Lost Password:
> > > > > http://www.tech-assist.org  and select "Login Problems?".
> > > > > Email Archives:
> > > > > http://www.freelists.org/archives/techassist/
> > > >
> > > >
> > >
> >
> ****************************************************************************
> > > *
> > > > Lost Password:
> > > > http://www.tech-assist.org  and select "Login Problems?".
> > > > Email Archives:
> > > > http://www.freelists.org/archives/techassist/
> > >
> > >
> > >
> >
> ****************************************************************************
> > *
> > > Lost Password:
> > > http://www.tech-assist.org  and select "Login Problems?".
> > > Email Archives:
> > > http://www.freelists.org/archives/techassist/
> > >
> > >
> >
> >
> ****************************************************************************
> *
> > Lost Password:
> > http://www.tech-assist.org  and select "Login Problems?".
> > Email Archives:
> > http://www.freelists.org/archives/techassist/
>
> *****************************************************************************
> Lost Password:
> http://www.tech-assist.org  and select "Login Problems?".
> Email Archives:
> http://www.freelists.org/archives/techassist/

*****************************************************************************
Lost Password:
http://www.tech-assist.org  and select "Login Problems?".
Email Archives:
http://www.freelists.org/archives/techassist/

Other related posts: