I believe that set has a Video Switching IC. Switches tuner out put and Ext1 and possibly Ext 2. Symptom will normally be no tuner Video, but OSD works, and if it has PIP, it will also be working. Using Video 1 and Video 2 will be normal. Now...are you sure about the Model #? -Ed- Ed Gaidies Tel-Tek Electronics Ontario-Canada teltek3@xxxxxxxxxxxx -----Original Message----- From: techassist-bounce@xxxxxxxxxxxxx [mailto:techassist-bounce@xxxxxxxxxxxxx] On Behalf Of al m Sent: Monday, December 22, 2003 10:22 AM To: techassist@xxxxxxxxxxxxx Subject: [TechAssist] Re: JVC-32050 Don't see many JVC's here. Sounds like you got a good one. Good luck. Al Marquardt ampm@xxxxxxx Al Marquardt Electronic Repair 206 W Main Girardville Pa. 17935 ----- Original Message ----- From: "S. Pasher" <spasher@xxxxxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Monday, December 22, 2003 10:12 PM Subject: [TechAssist] Re: JVC-32050 > Al thanks for reply. One of the things I forgot to mention in my original > email was that the OSD was good , also PIP was still working and had a good > picture. > Buck Pasher > Buck's TV > Gander Newfoundland > Canada > 709-256-7738 (Fax & Phone) > > > > ----- Original Message ----- > From: "al m" <ampm@xxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Sunday, December 21, 2003 11:36 PM > Subject: [TechAssist] Re: JVC-32050 > > > > Check the able circuit. If no parts are open then maybe the shot of > voltage > > to the heaters blew out a short in the tube. > > Al Marquardt > > ampm@xxxxxxx > > Al Marquardt Electronic Repair > > 206 W Main > > Girardville Pa. 17935 > > ----- Original Message ----- > > From: "S. Pasher" <spasher@xxxxxxxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Monday, December 22, 2003 9:53 AM > > Subject: [TechAssist] JVC-32050 > > > > > > > I've got a puzzle with this one. It came in with sound no picture. If > you > > > turned the screen up you could get a picture just before the overdrive > > lines > > > come on. > > > After chasing video all around the place and finding that waveforms were > > > about 1/4 what they should be coming out of the I/C that feeds the > > > pic.socket, I started to check the ABL cct. I found that it was 1.5 volt > > > low. Went to F/B found voltage low there also. My tech was checking in > > that > > > area and accidentally shorted pin 2 (ABL and Heater) to pin 3 (210 volts > > to > > > pic socket). the picture came back and after 2 hours running is still > > good. > > > I am wondering if anyone has had problems in this area before. I don't > > like > > > to give the TV back and have it fail again for same problem. I will run > it > > > for a day or two and if OK and I don't get any replies I will give it > > back. > > > > > > Buck Pasher > > > Buck's TV > > > Gander Newfoundland > > > Canada > > > 709-256-7738 (Fax & Phone) > > > > > > > > > > > > > > > > > > ************************************************************************ **** > > * > > > Lost Password: > > > http://www.tech-assist.org and select "Login Problems?". > > > Email Archives: > > > //www.freelists.org/archives/techassist/ > > > > > > > > > > > > > ************************************************************************ **** > * > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > > ************************************************************************ **** * > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ************************************************************************ ***** Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ***************************************************************************** Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/