My friend. I found problem . The cap c427(2200Uf) broken one leg between board and cap. use esr cap meter. found open.thank again. TV is fixed. Dang TVCR ----- Original Message ----- From: GJCHAMBERS <gjchambers@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, September 05, 2001 4:16 PM Subject: [TechAssist] Re: JVC TV av20920 vertical problem ,then can not turn on > > do you have the 24 volts to the vert output ic? > ----- Original Message ----- > From: "Trac Dang" <t8872695@xxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Wednesday, September 05, 2001 9:08 PM > Subject: [TechAssist] Re: JVC TV av20920 vertical problem ,then can not turn > on > > > > > > Hello. > > The problem is It is hard to turn on. The tv must be reset. but it is > > sometimes turn on sometimes not. when it is turn on it willshut down in > 30 > > seconds.I already changed vertical ic.same thing, no fix .one line at the > > center.I will change ic 703 . 5v regulator > > (5pin) . it also hard to find this ic 78LR05.Thank you for the tip. > > Dang tvcr > > ----- Original Message ----- > > From: GJCHAMBERS <gjchambers@xxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Wednesday, September 05, 2001 1:33 PM > > Subject: [TechAssist] Re: JVC TV av20920 vertical problem ,then can not > turn > > on > > > > > > > > > > make sure you have the 24 volts to ic, > > > the microprocessor monitors the vert for pulses and if not present will > > shut > > > off the tv in error mode. then the led blinks the error code. power must > > be > > > removed before error code will reset.once you get vertical problem > fixed, > > > set will stay on. > > > occasionally when the vert ic shorts, it will also damage the micro as > > well. > > > if this happens, you will get ok picture but set will still error and > turn > > > off. > > > gary > > > ----- Original Message ----- > > > From: "Fernand Goguen" <fgoguen@xxxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Wednesday, September 05, 2001 2:35 PM > > > Subject: [TechAssist] Re: JVC TV av20920 vertical problem ,then can not > > turn > > > on > > > > > > > > > > > > > > > > > > ----- Original Message ----- > > > > From: "tomlee" <t8872695@xxxxxxxxxxxxx> > > > > To: <techassist@xxxxxxxxxxxxx> > > > > Sent: Tuesday, September 04, 2001 10:05 PM > > > > Subject: [TechAssist] JVC TV av20920 vertical problem ,then can not > turn > > > on > > > > > > > > > > > > > Seems to me that I read a previous post on JVC TV,s and the problem > > was > > > a > > > > bad yoke. I had one last year. Customer didn,t want to have it > repaired. > > > > Have you checked the yoke? Fernand Goguen Goguen TV Service. > > > > > Hello techs. > > > > > Have JVC in shop. model AV 20920. only a line at the center > > horizontaly. > > > I > > > > > already changed vertical ic .no fix. Turn on unit It run about 1 > > minute > > > > then > > > > > relay click off. > > > > > with led blink.Suddenly now I can not turn on any more by remote or > > > power > > > > > button. > > > > > Notice there is alot pest inside the tv . May be these pest short > the > > > > > epprom. Ic705 > > > > > .Any idea is appriciated. Dang TVCR > > > > > > > > > > Help make your TechAssist online repair tips > > > > > database better! Submit your fixes here: > > > > > http://www.circuitwork.com/techassist/tip/#tips > > > > > To unsubscribe write to: > > > > > techassist-request@xxxxxxxxxxxxx > > > > > with unsubscribe in the subject line. > > > > > > > > Help make your TechAssist online repair tips > > > > database better! Submit your fixes here: > > > > http://www.circuitwork.com/techassist/tip/#tips > > > > To unsubscribe write to: > > > > techassist-request@xxxxxxxxxxxxx > > > > with unsubscribe in the subject line. > > > > > > Help make your TechAssist online repair tips > > > database better! Submit your fixes here: > > > http://www.circuitwork.com/techassist/tip/#tips > > > To unsubscribe write to: > > > techassist-request@xxxxxxxxxxxxx > > > with unsubscribe in the subject line. > > > > Help make your TechAssist online repair tips > > database better! Submit your fixes here: > > http://www.circuitwork.com/techassist/tip/#tips > > To unsubscribe write to: > > techassist-request@xxxxxxxxxxxxx > > with unsubscribe in the subject line. > > Help make your TechAssist online repair tips > database better! Submit your fixes here: > http://www.circuitwork.com/techassist/tip/#tips > To unsubscribe write to: > techassist-request@xxxxxxxxxxxxx > with unsubscribe in the subject line. Help make your TechAssist online repair tips database better! Submit your fixes here: http://www.circuitwork.com/techassist/tip/#tips To unsubscribe write to: techassist-request@xxxxxxxxxxxxx with unsubscribe in the subject line.