----- Original Message ----- From: "javiles6" <javiles6@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, June 10, 2004 2:26 AM Subject: Re: [TechAssist] Re: Fw: Panasonics Mod# CTP-2764S (Vertical foldover) > Eric > > The chassis # for this set is AREDP204. And for those who reply, yes i have > replace all the 400 series caps, except C452 which is an oval capacitor and > i don`t have one in stock. About ringing the yoke, no i haven`t cause i > don`t have a ringer. All of my expensive equipment were stolen in the last > shop that i had in NY. Ever since i have try to just go with the least > expensive equipment. But here is a read out of all the voltages i have in > all the pins. Perhaps someone could look up this voltages and tell me is > they are right or wrong. > > IC451 > > 1= 11.9v > 2= 5.7v > 3= 5.9v > 4= 0v > 5= 6.4v > 6= 4.4v > 7= 26.7v > 8= 0v > 9= 0.6v > 10= GND > 11= 11.4v > 12= 26v > 13= 5v > > Hope this info will help > > Thanks to those that reply > > Jose > ----- Original Message ----- > From: "Eric Manuel" <tvman@xxxxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Wednesday, June 09, 2004 5:44 PM > Subject: [TechAssist] Re: Fw: Panasonics Mod# CTP-2764S (Vertical foldover) > > > > Jose any chassis# on it I may be able to get a print..Eric > > E M Electronics > > Deer Lake Nfld > > Eric Manuel > > > > javiles6 wrote: > > > > > > techs > > > > > > since i have not receive any reply to this message, what about a voltage > pin > > > out for this IC. If i could just get the right voltages i could take it > from > > > there. This it why is hard to work without an schematic, and you can not > > > charge the customer for this because the labor will be too high. And if > you > > > buy the schematic with what you are going to charge for the labor then > you > > > will only get a profit of perhaps $20.00 to $30.00 dollars. So any help > is > > > appreciated. > > > > > > Thanks > > > > > > Jose > > > ----- Original Message ----- > > > From: "javiles6" <javiles6@xxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Tuesday, June 08, 2004 10:01 PM > > > Subject: [TechAssist] Panasonics Mod# CTP-2764S (Vertical foldover) > > > > > > > Hello techs > > > > This set came in with a verical line across the middle of the set. I > > > resolder the verical IC(IC451) but with no help, so i replace it with an > NTE > > > 7085. Now the set is about 4" open but with verical foldover. I have > change > > > C455(100uf/35v which was out of tolerance and C451(220uf/16V) but with > no > > > help. I have the 12V at pin one of IC and the 26v at pin 7, also at pin > 12. > > > All of the other pin run from 5v to 6v, except pin 10 which GND and pin > 9 > > > OSC BLOCKING. I don`t have an schematic to be certain that this are the > > > correct voltages. Does any one have the vertical section that could > e-mail > > > me or any help that could offer. Your help is always appreciated. > > > > > > > > Thanks > > > > > > > > Jose > > > > > > > > Aviles Computer & TV Repairs > > > > 508 Bingaman st > > > > Reading, PA 19602 > > > > Tel # 610-478-1342 > > > > > > > > > -------------------------------------------------------------------------- > > > --- > > > > Lost Password: > > > > http://www.tech-assist.org and select "Login Problems?". > > > > Email Archives: > > > > //www.freelists.org/archives/techassist/ > > > > > > > -------------------------------------------------------------------------- > --- > > > Lost Password: > > > http://www.tech-assist.org and select "Login Problems?". > > > Email Archives: > > > //www.freelists.org/archives/techassist/ > > > > -------------------------------------------------------------------------- > --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/