[TechAssist] Re: Dead CTC 169-low 14v -detailed symptonsTECH

Al, I had this saved from a previous email I sent...
some of these you may have checked, but I'm just
posting all of it.

Replace CR4118, C4108, CR4402, C4402 & C4401
even if they check good.  Also check CR4101, CR4606,
CR4111, C4105, Q4101, CR4122, CR4123, R4150, R1928,
R4114, C4705, C4115, CR4709, C4145, C414, CR3101,
R4150, C4141, SCR501, CR4504, C4503, R3126, CR4303,
CR4710, C4145, Q4105, R4102, C3124, R4704, R4713,
Q3102, R4904, U4101, the yoke, pin of 12-13 of T4102
could be open, resolder L4803 & T4401, and possibly
L4702, U4801, U1902, Q4302 check for shorts (pin 1-3) in
U1901 If you are getting ~15v from the PS, IC3101 & Q4601
could be bad.  If it's down below 15v, replace C4145.  Could
also be HV distribution block.
-Clint

http://orpheuscomputing.com
Clint Hamilton, Owner
sales@xxxxxxxxxxxxxxxxxxxx
Tech-Assist Administration
http://tech-assist.org
techassist@xxxxxxxxxxxxx

----- Original Message -----
From: "AL LEATHERMAN" <alleathe@xxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, August 30, 2001 8:03
Subject: [TechAssist] Dead CTC 169-low 14v -detailed
symptonsTECH



Thanks Dan,
    Working late last night,so I screwed up on symptoms! The
160 volts is on
collector of the reg (Q4101)the h.out (Q4401)is 120 volts.The
reg pulses
from zero to about 250 volts (peak to peak).The 120 volts is
steady(no
load?)the 14volts is down to 8 volts.The 5 volt standby is
ok.I suspect a
load on the 14 volt line.
   The horizontal never fires up even if I power pin # 25 on
Ul001
with external 9 volts.There is no driving pulse at #23
(U1001) with the 9
volts on #26.The shutdown pin remains at zero.
    I am going to replace Q4101 later, even though it isn't
shorted and
obviously is driven.
    When keyed "on" with remote
the "on" pin on the micro jumps for a split second and
remains low.
    I suspect lightning damage as this came in after a stirm
period.
appreciate any help. I will post when fixed. al

Al's TV
224 Rt. 46
Mine Hill, NJ. 07803
973-361-5796
alleathe@xxxxxxxxxxxxx
----- Original Message -----
From: "Daniel" <danielstarca@xxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, August 30, 2001 12:27 AM
Subject: [TechAssist] Re: Fw: CTC169 14volts down to
8volts-dead set


>
> Dear Al:
>  That Horizontal Output Transistor Collector voltage
> is way too high.I think you are observing Regulator
> action(shut down intiated by Micro).
>  Suspect components around That I.C. you
> changed,especially the two diodes cr4401,cr4402.
> -Daniel
>
> --- AL LEATHERMAN <alleathe@xxxxxxxxxxxxx> wrote:
> >
> >
> > Subject: CTC169 14volts down to 8volts-dead set
> >
> >
> > > All: changed ic driving chopper-chopper pulses at
> > about 200 volts peak to
> > > peak,160 volts on hor.out.
> > > no pulse from jungle ic to hor driver, even with 9
> > volts applied to jungle
> > > ic. Micro produces on pulse briefly but stays
> > low.Appreciate help. also
> > > rerplaced famous diode
> > > in 14 volt/5 volt stand by circuit. al
> > >
> > > Al's TV
> > > 224 Rt. 46
> > > Mine Hill, NJ. 07803
> > > 973-361-5796
> > > alleathe@xxxxxxxxxxxxx
> > >
> >
> > Help make your TechAssist online repair tips
> > database better!  Submit your fixes here:
> > http://www.circuitwork.com/techassist/tip/#tips
> > To unsubscribe write to:
> > techassist-request@xxxxxxxxxxxxx
> > with  unsubscribe  in the subject line.
>
>
> __________________________________________________
> Do You Yahoo!?
> Get email alerts & NEW webcam video instant messaging with
Yahoo!
Messenger
> http://im.yahoo.com
> Help make your TechAssist online repair tips
> database better!  Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with  unsubscribe  in the subject line.

Help make your TechAssist online repair tips
database better!  Submit your fixes here:
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx
with  unsubscribe  in the subject line.



Help make your TechAssist online repair tips 
database better!  Submit your fixes here: 
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx 
with  unsubscribe  in the subject line.

Other related posts: