[TechAssist] Re: CTC177AA2/3 Need menu access for max. volume.

I said all fuctions normal enought B/S on this subject
do it your way.


--- "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> wrote:
> 
> If they are really preprogramed,  why do you have to
> reset the Horz
> parameters??  the tuner parameters must be saved or
> you will probably have
> snowy channels esp. above 47 or so. The so called
> preprogramed eeproms are
> just set to a average values and not necessarily 
> exact for your TV.
> However if you don't have these higher channels in
> your area it may seem
> aligned OK
> Phillip R Hull
> phil245@xxxxxxxxxxxxx
> ----- Original Message -----
> From: "Richard Golden" <reldong@xxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, October 30, 2001 2:46 PM
> Subject: [TechAssist] Re: CTC177AA2/3 Need menu
> access for max. volume.
> 
> 
> >
> > I have repaired over 200 rca ge tvs always solder
> > tuner
> > never change eprom unless needed. i install
> > preprogramed eproms. and only, have to set horiz.
> > never had any problems grounding r916? all
> funtions
> > work fine?
> > richard
> >
> >
> > --- Ralph Dorsey <Merlin-Wizard@xxxxxxxxxxxxxxxx>
> > wrote:
> > > although these "tricks might work", your not
> fixing
> > > the real
> > > problem,,,it starts with the turner grounds
> going
> > > intermittent, then the
> > > eeprom becomes corrupted. Even though changing
> the
> > > eeporm might be
> > > intimidating to some , it's the correct repair.
> If
> > > the sound part of the
> > > eeprom is corrupted, you can bet that other
> critical
> > > values have also.
> > > Do the right thing and use the chipper checker.
> In
> > > the instructions it
> > > gives a layout for the clip needed for the
> > > ctc177/187. You need to make
> > > this so you can reinitialize the eeprom and
> reset
> > > those areas of the
> > > chip you can't get to with the service menu.
> Once
> > > you make and learn how
> > > to use this, it only takes about a minute to do
> > > that. ( of course you
> > > still need to solder up the tuner  and chassis)
> > >
> > > Richard Golden wrote:
> > >
> > > >no, but i always go the shortest way to
> ground,the
> > > end
> > > >of r1916 (r916) closest to the base of q1903
> mute
> > > >transistor
> > > >works fine never had a reservice on this trick
> have
> > > >done a lot good money manker we need every
> break we
> > > >can
> > > >get ,good luck
> > > >richard
> > > >
> > > >
> > > >--- info@xxxxxxxxxxxxxxx wrote:
> > > >
> > > >>From: "tech-rep" <tech-rep@xxxxxxxxxx>
> > > >>
> > > >>Hello Richard,
> > > >>
> > > >>Re: CTC177AA2/3 Need menu access for max.
> volume;
> > > >>low volume.
> > > >>
> > > >>Thank you for your tip. Just one more thing.
> > > >>Just for the record, does it matter which side
> of
> > > >>R916 is
> > > >>grounded?
> > > >>
> > > >>Denise Adams
> > > >>tech-rep@xxxxxxxxxx
> > > >>
> > > >>----- Original Message -----
> > > >>From: "Richard Golden" <reldong@xxxxxxxxx>
> > > >>To: <techassist@xxxxxxxxxxxxx>
> > > >>Sent: Wednesday, October 24, 2001 3:56 PM
> > > >>Subject: [TechAssist] Re: CTC177AA2/3 Need
> menu
> > > >>access for
> > > >>max. volume.
> > > >>
> > > >>
> > > >>on the ctc187ab and others i solder toground
> r916,
> > > >>vol
> > > >>comes back.
> > > >>
> > > >>
> > > >>--- albert marquardt <ampm@xxxxxxx> wrote:
> > > >>
> > > >>>the third menu is the tuner menu. replace the
> > > >>>
> > > >>epprom
> > > >>
> > > >>>but before replacing it
> > > >>>write down all original settings, or get a
> > > >>>programmed epprom. i have never
> > > >>>seen a menu for max. volume.
> > > >>>al marquardt
> > > >>>ampm@xxxxxxx
> > > >>>----- Original Message -----
> > > >>>From: <info@xxxxxxxxxxxxxxx>
> > > >>>To: TechAssist <techassist@xxxxxxxxxxxxx>
> > > >>>Sent: Tuesday, October 23, 2001 7:48 PM
> > > >>>Subject: [TechAssist] CTC177AA2/3 Need menu
> > > access
> > > >>>for max. volume.
> > > >>>
> > > >>>
> > > >>>>From: Denise Adams
> > > >>>>tech-rep@xxxxxxxxxx
> > > >>>>
> > > >>>>I need; CTC177AA2/3 Need menu access for
> max.
> > > >>>>
> > > >>>volume.
> > > >>>
> > > >>>>This set is not like the CTC176. The third
> menu,
> > > >>>>allows access to minimum and maximum volume
> > > >>>>control. How do I adjust manually or by
> menu?
> > > >>>>Didn't see a manual adjustment. I have the
> > > >>>>
> > > >>>original remote.
> > > >>>
> > > >>>>It doesn't access the volume menu.
> > > >>>>
> > > >>>>Any help appreciated.
> > > >>>>Thanks in advance.
> > > >>>>Denise Adams
> > > >>>>tech-rep@xxxxxxxxxx
> > > >>>>
> > > >>=====
> > > >>Richard Golden
> > > >>Golden Video Repair Center
> > > >>1214 e. 6th street
> > > >>ontario ca. 91764
> > > >>(909)988-3356
> > > >>
> > > >>
> > > >>
> > > >>Help make your TechAssist online repair tips
> > > >>database better!  Submit your fixes here:
> > >
> >>http://www.circuitwork.com/techassist/tip/#tips
> > > >>To unsubscribe write to:
> > > >>techassist-request@xxxxxxxxxxxxx
> > > >>with  unsubscribe  in the subject line.
> > > >>
> > > >
> > > >
> > > >=====
> > > >Richard Golden
> > > >Golden Video Repair Center
> > > >1214 e. 6th street
> > > >ontario ca. 91764
> > > >(909)988-3356
> > > >
> > > >reldong@xxxxxxxxx
> > > >Help make your TechAssist online repair tips
> > > >database better!  Submit your fixes here:
> > > >http://www.circuitwork.com/techassist/tip/#tips
> > > >To unsubscribe write to:
> > > >techassist-request@xxxxxxxxxxxxx
> > > >with  unsubscribe  in the subject line.
> > > >
> > >
> > >
> > >
> > > Help make your TechAssist online repair tips
> > > database better!  Submit your fixes here:
> 
=== message truncated ===


=====
Richard Golden
Golden Video Repair Center
1214 e. 6th street
ontario ca. 91764
(909)988-3356

reldong@xxxxxxxxx
Help make your TechAssist online repair tips 
database better!  Submit your fixes here: 
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx 
with  unsubscribe  in the subject line.

Other related posts: