[TechAssist] Re: Best way to clean a head.

  • From: <abandb@xxxxxxxxxxxxx>
  • To: techassist@xxxxxxxxxxxxx
  • Date: Mon, 26 Nov 2001 20:13:41 -0500

USE COFFEE FILTERS FROM abandb@xxxxxxxxxxxxx
> 
> From: "Jeff Dougherty" <jeff@xxxxxxxxxxxxxxxxxx>
> Date: 2001/11/26 Mon PM 03:30:48 EST
> To: <techassist@xxxxxxxxxxxxx>
> Subject: [TechAssist] Re: Best way to clean a head.
> 
> 
> Clint,
> There are two different types of chamois swabs. The more expensive ones do
> not have the 'fibers' you spoke of.
> I've used both and have never damaged a head.
> I know the ones with the visible fibers, but these have not broken any of
> the heads.
> Now the "foam' swabs you talk about....aren't they pretty much like the
> auto-head cleaner swabs?
> 
> Jeff
> mailto:Jeff@xxxxxxxxxxxxxxxxxx  www.9-11-2001tragedy.com
> FAX 1-413-280-0677
> Intrepid Video & Electronics
> Harrisburg, PA 17111
> 717-909-8844
> www.intrepid-video.com www.tech-repair.net www.thetoolcaddy.com
> ----- Original Message -----
> From: "OrpheusComputing.com Repair" <techassist@xxxxxxxxxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Monday, November 26, 2001 2:05 AM
> Subject: [TechAssist] Re: Best way to clean a head.
> 
> 
> >
> > Anyone ever use foam swabs?  After many other things, this is
> > all I like.  I ruined heads once....ONCE with chamois swab.
> > Chamois has fibers on it, like little "hairs" that can get
> > caught on the head chip.  I noticed this many times, but
> > since they were indeed "video head cleaning swabs", I kept
> > using them; until one was ruined.  (Maybe it was some cheap
> > chamois).  A few years back I started getting some video head
> > cleaner in a spray can from MAT.  It's sort of like contact
> > cleaner (trichlorethane based I think, or other rapid
> > evaporative chemical).  Spay them with that then use to the
> > foam swab to remove debris.  Preferably I like to remove the
> > top of the drum, then use compressed air to blow OUT from the
> > center of the head drum to blow out the 'striped oxides and
> > tape particulates' that are always within the head drum, then
> > clean them.  (I looked on the can of head cleaner, and it's
> > "Chemtronics Head Cleaner" #C2420.  Trichlorotrifluoroethane
> > based w/a few other ingredients).
> > -Clint
> >
> > Happy Thanksgiving &
> > God Bless Us All
> > Clint Hamilton, Owner
> > http://OrpheusComputing.com
> > http://ComputerHardware-ConsumerElectronics.com
> > sales@xxxxxxxxxxxxxxxxxxxx
> > Fax: 209-882-9602
> > TechAssist Administration
> > http://tech-assist.org
> > techassist@xxxxxxxxxxxxx
> >
> > ----- Original Message -----
> > From: "Jeff Dougherty" <jeff@xxxxxxxxxxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Sunday, November 25, 2001 10:48 PM
> > Subject: [TechAssist] Re: Best way to clean a head.
> >
> >
> >
> > I prefer NOT to use cotton swabs, period.
> > Chamois swabs have been working fine for me. I have used the
> > business card
> > method, but not much luck with that one.
> > On the tough ones, I remove the cylinder and soak in Acetone
> >
> >
> > Jeff
> > mailto:Jeff@xxxxxxxxxxxxxxxxxx  www.9-11-2001tragedy.com
> > FAX 1-413-280-0677
> > Intrepid Video & Electronics
> > Harrisburg, PA 17111
> > 717-909-8844
> > www.intrepid-video.com www.tech-repair.net
> > www.thetoolcaddy.com
> > ----- Original Message -----
> > From: "Richard Golden d.b.a. Golden Video Repair Center"
> > <reldong@xxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Sunday, November 25, 2001 3:44 PM
> > Subject: [TechAssist] Re: Best way to clean a head.
> >
> >
> > >
> > > I forgot to say use only the name brand qtips they are made
> > with wood and
> > > cotton others are made with plastic
> > > and cotton and mek will melt them
> > > RICHARD
> > >
> > > ---- Original Message -----
> > > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Saturday, November 24, 2001 5:26 PM
> > > Subject: [TechAssist] Re: Best way to clean a head.
> > >
> > >
> > > > I don't like Qtips for any kind of electronic cleaning.
> > Too many cotton
> > > fibers
> > > > to deal with.
> > > > Dennis Viereck
> > > >
> > > > Jeff Dougherty wrote:
> > > >
> > > > > Richard,
> > > > > you use Q-tips on video heads?
> > > > > Now that is a new one. How do you keep the cotton
> > fibers from ripping
> > > the
> > > > > heads?
> > > > >
> > > > > Jeff
> > > > > mailto:Jeff@xxxxxxxxxxxxxxxxxx
> > www.9-11-2001tragedy.com
> > > > > FAX 1-413-280-0677
> > > > > Intrepid Video & Electronics
> > > > > Harrisburg, PA 17111
> > > > > 717-909-8844
> > > > > www.intrepid-video.com www.tech-repair.net
> > www.thetoolcaddy.com
> > > > > ----- Original Message -----
> > > > > From: "Richard Golden d.b.a. Golden Video Repair
> > Center"
> > > <reldong@xxxxxxxxx>
> > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > Sent: Saturday, November 24, 2001 5:17 PM
> > > > > Subject: [TechAssist] Re: Best way to clean a head.
> > > > >
> > > > > >
> > > > > > I've used mek (methyl ethyl ketone) and qtips for 15
> > yrs
> > > > > > 3 shops over I,ooo 's of vcrs tried everything else
> > first
> > > > > > works best and I quart last a long time. buy from
> > home depo etc. had
> > a
> > > > > > customer who was a chemist find it for me. Will EAT
> > plastic!!! can
> > use
> > > on
> > > > > > all heads audio ,
> > > > > > video tape guides pinch rollers pc boards but no soft
> > Plastic!!cleans
> > > > > rubber
> > > > > > ok
> > > > > > Richard
> > > > > >
> > > > > > ---- Original Message -----
> > > > > > From: "Tel-Tek Electronics" <teltek@xxxxxxxxxxx>
> > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > Sent: Friday, November 23, 2001 8:33 AM
> > > > > > Subject: [TechAssist] Re: Best way to clean a head.
> > > > > >
> > > > > >
> > > > > > >
> > > > > > > Hey guys........
> > > > > > > I use an Ultrasonic Denture Cleaner.
> > > > > > > Use Isopropyl alcohol in the unit.
> > > > > > > Unit has an airtight lid on it so the alcohol
> > doesn't disperse
> > > between
> > > > > > uses.
> > > > > > > Works wonders on any parts that need cleaning.
> > > > > > >
> > > > > > > -Ed-
> > > > > > >
> > > > > > > teltek@xxxxxxxxxxx
> > > > > > > TEL-TEK ELECTRONICS.
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > ----- Original Message -----
> > > > > > > From: "Leonard G. Caillouet" <lcaillo@xxxxxxxxxxxx>
> > > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > > Sent: Friday, November 23, 2001 11:03 AM
> > > > > > > Subject: [TechAssist] Re: Best way to clean a head.
> > > > > > >
> > > > > > >
> > > > > > > >
> > > > > > > > I also use denatured alcolhol but use strips of
> > synthetic
> > chamois
> > > ( it
> > > > > > > holds
> > > > > > > > up better without giving up little bits and is
> > smoother than
> > > natural).
> > > > > > If
> > > > > > > > you fold it into several layers it will hold
> > enough solvent to
> > get
> > > the
> > > > > > > > dirtiest heads clean and allows you to put a good
> > deal of
> > pressure
> > > on
> > > > > > the
> > > > > > > > head drum.  I run the head with a dummy cassette
> > and rarely have
> > a
> > > > > head
> > > > > > > that
> > > > > > > > doesn't clean on the first try.  You can throw
> > these synthetic
> > > chamois
> > > > > > > into
> > > > > > > > the washer several times before you replace them
> > and the whole
> > > thing
> > > > > > will
> > > > > > > > last years.
> > > > > > > >
> > > > > > > > Leon.
> > > > > > > >
> > > > > > > > Leonard G. Caillouet
> > > > > > > > Service Manager
> > > > > > > > Electronics World
> > > > > > > > Gainesville, FL
> > > > > > > > 352-332-5608
> > > > > > > > 352-332-5668 (fax)
> > > > > > > >
> > > > > > > > ----- Original Message -----
> > > > > > > > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx>
> > > > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > > > Sent: Friday, November 23, 2001 12:20 AM
> > > > > > > > Subject: [TechAssist] Re: Best way to clean a
> > head.
> > > > > > > >
> > > > > > > >
> > > > > > > > >
> > > > > > > > > I just use plain white printer paper and
> > denatured alcohol.
> > cut
> > > the
> > > > > > > paper
> > > > > > > > in 1
> > > > > > > > > inch wide strips 4 inches long. Soak one end of
> > the paper in
> > the
> > > > > > alcohol
> > > > > > > > and place
> > > > > > > > > it against the video hear drum with my finger
> > on the other
> > side.
> > > > > > Rotate
> > > > > > > > the the
> > > > > > > > > drum with a little pressure but no movement of
> > my finger. I
> > > inspect
> > > > > > the
> > > > > > > > cleaning
> > > > > > > > > with a machinist microscope and make sure the
> > head is clean
> > and
> > > no
> > > > > > > debris
> > > > > > > > left
> > > > > > > > > over. I have used this method since the VBT200
> > days. Works
> > > great! As
> > > > > > > long
> > > > > > > > as you
> > > > > > > > > dry it with a slight puff of compressed air
> > before tossing a
> > > tape in
> > > > > > the
> > > > > > > > machine.
> > > > > > > > >
> > > > > > > > > Dennis Viereck
> > > > > > > > >
> > > > > > > > > Ralph Dorsey wrote:
> > > > > > > > >
> > > > > > > > > > a small piece of chamois cloth works great
> > also (and it's
> > > > > re-usable)
> > > > > > > > > >
> > > > > > > > > > Ray Lufkin wrote:
> > > > > > > > > >
> > > > > > > > > > > Best way is to use a business card soaked
> > in acetone. Hold
> > > it up
> > > > > > > > against the
> > > > > > > > > > > head and turn the head the standard
> > direction (cc). That
> > > will
> > > > > > > usually
> > > > > > > > clean
> > > > > > > > > > > the most stubborn clog.
> > > > > > > > > > >
> > > > > > > > > > > u
> > > > > > > > > > > ----- Original Message -----
> > > > > > > > > > > From: "Phillip R. Hull"
> > <phil245@xxxxxxxxxxxxx>
> > > > > > > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > > > > > > Sent: Tuesday, November 20, 2001 4:44 PM
> > > > > > > > > > > Subject: [TechAssist] Re: Question
> > reguarding Panasonic
> > VCRs
> > > > > > > > > > >
> > > > > > > > > > > >
> > > > > > > > > > > > A worn head drum will show a full picture
> > with a small
> > > area
> > > > > > thats
> > > > > > > > > > > distorted.
> > > > > > > > > > > > Its caused because the tape no longer
> > touches the head
> > > drum,
> > > > > > the
> > > > > > > > full
> > > > > > > > > > > width
> > > > > > > > > > > > of the tape. This is caused by a air gap
> > between the
> > tape
> > > and
> > > > > > the
> > > > > > > > head.
> > > > > > > > > > > >
> > > > > > > > > > > > Phillip R Hull
> > > > > > > > > > > > phil245@xxxxxxxxxxxxx
> > > > > > > > > > > > ----- Original Message -----
> > > > > > > > > > > > From: "George Winters"
> > <littletiger67@xxxxxxxxx>
> > > > > > > > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > > > > > > > Sent: Tuesday, November 20, 2001 3:59 PM
> > > > > > > > > > > > Subject: [TechAssist] Re: Question
> > reguarding Panasonic
> > > VCRs
> > > > > > > > > > > >
> > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > >  Howdy Wally,
> > > > > > > > > > > > > If the heads are bad there won't be any
> > video showing
> > on
> > > the
> > > > > > > > screen, if
> > > > > > > > > > > > you have even and inch of video showing
> > on the screen
> > the
> > > > > heads
> > > > > > > are
> > > > > > > > good,
> > > > > > > > > > > > clean them again. I've had some vcrs unit
> > in my shop
> > that
> > > > > would
> > > > > > > have
> > > > > > > > to be
> > > > > > > > > > > > cleaned 6 times to clean the heads out.
> > Hope this help
> > > you.
> > > > > > > > > > > > > George Winters Jr.
> > > > > > > > > > > > > GLW CUSTOM ELECTRONICS
> > > > > > > > > > > > > TN.
> > > > > > > > > > > > >   Jeff Dougherty
> > <jeff@xxxxxxxxxxxxxxxxxx> wrote:
> > > > > > > > > > > > > Wally,
> > > > > > > > > > > > > If these things have the spongy self
> > cleaners..this is
> > > more
> > > > > > than
> > > > > > > > likely
> > > > > > > > > > > > the
> > > > > > > > > > > > > cause. What a sales gimmick!
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > > Jeff
> > > > > > > > > > > > > mailto:Jeff@xxxxxxxxxxxxxxxxxx
> > www.9-11-2001tragedy.com
> > > > > > > > > > > > > FAX 1-413-280-0677
> > > > > > > > > > > > > Intrepid Video & Electronics
> > > > > > > > > > > > > Harrisburg, PA 17111
> > > > > > > > > > > > > 717-909-8844
> > > > > > > > > > > > > www.intrepid-video.com
> > www.tech-repair.net
> > > > > > www.thetoolcaddy.com
> > > > > > > > > > > > > ----- Original Message -----
> > > > > > > > > > > > > From: "Wally Heise"
> > > > > > > > > > > > > To:
> > > > > > > > > > > > > Sent: Tuesday, November 20, 2001 1:39
> > AM
> > > > > > > > > > > > > Subject: [TechAssist] Question
> > reguarding Panasonic
> > VCRs
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > > >
> > > > > > > > > > > > > > I now have about 4 Panasonic vcrs
> > which all have
> > what
> > > > > > appears
> > > > > > > to
> > > > > > > > be
> > > > > > > > > > > bad
> > > > > > > > > > > > > > video heads when you play. All of
> > these vcrs are 1-4
> > > years
> > > > > > old
> > > > > > > > and
> > > > > > > > > > > > > > different model numbers. I don't have
> > a video head
> > > tester
> > > > > to
> > > > > > > > check the
> > > > > > > > > > > > > > heads yet, (have not had a big need
> > for one). I am
> > > > > wondering
> > > > > > > if
> > > > > > > > others
> > > > > > > > > > > > > > have seen a high failure rate with
> > Panasonic video
> > > heads?
> > > > > Or
> > > > > > > is
> > > > > > > > there
> > > > > > > > > > > > > > something else I'm missing? Is there
> > an easy method
> > of
> > > > > > > > determining if
> > > > > > > > > > > a
> > > > > > > > > > > > > > video head is defective, without the
> > tester?
> > Needless
> > > to
> > > > > say
> > > > > > I
> > > > > > > > have
> > > > > > > > > > > > > > cleaned and cleaned the heads to no
> > avail.
> > > > > > > > > > > > > >
> > > > > > > > > > > > > > Any help is greatly appreciated.
> > > > > > > > > > > > > >
> > > > > > > > > > > > > > Thank you
> > > > > > > > > > > > > > Wally Heise
> > > > > > > > > > > > > > South Isle Repair
> > > > > > > > > > > > > > =================================
> > > > > > > > > > > > > > Help make your TechAssist database
> > better!
> > > > > > > > > > > > > > Submit your fixes here:
> > > > > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > > > > > =================================
> > > > > > > > > > > > > > To UNSUBSCRIBE your email address,
> > click here:
> > > > > > > > > > > > > >
> > techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > > > > > > >
> > > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > > =================================
> > > > > > > > > > > > > Help make your TechAssist database
> > better!
> > > > > > > > > > > > > Submit your fixes here:
> > > > > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > > > > =================================
> > > > > > > > > > > > > To UNSUBSCRIBE your email address,
> > click here:
> > > > > > > > > > > > >
> > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > > > ---------------------------------
> > > > > > > > > > > > > Do You Yahoo!?
> > > > > > > > > > > > > Yahoo! GeoCities - quick and easy web
> > site hosting,
> > just
> > > > > > > > $8.95/month.
> > > > > > > > > > > > >
> > > > > > > > > > > > > =================================
> > > > > > > > > > > > > Help make your TechAssist database
> > better!
> > > > > > > > > > > > > Submit your fixes here:
> > > > > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > > > > =================================
> > > > > > > > > > > > > To UNSUBSCRIBE your email address,
> > click here:
> > > > > > > > > > > > >
> > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > > > > > >
> > > > > > > > > > > > >
> > > > > > > > > > > >
> > > > > > > > > > > > =================================
> > > > > > > > > > > > Help make your TechAssist database
> > better!
> > > > > > > > > > > > Submit your fixes here:
> > > > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > > > =================================
> > > > > > > > > > > > To UNSUBSCRIBE your email address, click
> > here:
> > > > > > > > > > > >
> > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > > > > >
> > > > > > > > > > > >
> > > > > > > > > > >
> > > > > > > > > > > =================================
> > > > > > > > > > > Help make your TechAssist database better!
> > > > > > > > > > > Submit your fixes here:
> > > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > > =================================
> > > > > > > > > > > To UNSUBSCRIBE your email address, click
> > here:
> > > > > > > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > > >
> > > > > > > > > > =================================
> > > > > > > > > > Help make your TechAssist database better!
> > > > > > > > > > Submit your fixes here:
> > > > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > > =================================
> > > > > > > > > > To UNSUBSCRIBE your email address, click
> > here:
> > > > > > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > > >
> > > > > > > > > =================================
> > > > > > > > > Help make your TechAssist database better!
> > > > > > > > > Submit your fixes here:
> > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > > =================================
> > > > > > > > > To UNSUBSCRIBE your email address, click here:
> > > > > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > >
> > > > > > > >
> > > > > > > > =================================
> > > > > > > > Help make your TechAssist database better!
> > > > > > > > Submit your fixes here:
> > > http://circuitwork.com/techassist/tip/#tips
> > > > > > > > =================================
> > > > > > > > To UNSUBSCRIBE your email address, click here:
> > > > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > > > >
> > > > > > >
> > > > > > > =================================
> > > > > > > Help make your TechAssist database better!
> > > > > > > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > > > > > > =================================
> > > > > > > To UNSUBSCRIBE your email address, click here:
> > > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > >
> > > > > > ----------------------------------------------------
> > > > > > Sign Up for NetZero Platinum Today
> > > > > > Only $9.95 per month!
> > > > > > http://my.netzero.net/s/signup?r=platinum&refcd=PT97
> > > > > > =================================
> > > > > > Help make your TechAssist database better!
> > > > > > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > > > > > =================================
> > > > > > To UNSUBSCRIBE your email address, click here:
> > > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > >
> > > > > >
> > > > >
> > > > > =================================
> > > > > Help make your TechAssist database better!
> > > > > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > > > > =================================
> > > > > To UNSUBSCRIBE your email address, click here:
> > > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > >
> > > >
> > > > =================================
> > > > Help make your TechAssist database better!
> > > > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > > > =================================
> > > > To UNSUBSCRIBE your email address, click here:
> > > >
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >
> > > ----------------------------------------------------
> > > Sign Up for NetZero Platinum Today
> > > Only $9.95 per month!
> > > http://my.netzero.net/s/signup?r=platinum&refcd=PT97
> > > =================================
> > > Help make your TechAssist database better!
> > > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > > =================================
> > > To UNSUBSCRIBE your email address, click here:
> > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >
> > >
> >
> > =================================
> > Help make your TechAssist database better!
> > Submit your fixes here:
> > http://circuitwork.com/techassist/tip/#tips
> > =================================
> > To UNSUBSCRIBE your email address, click here:
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> >
> >
> >
> > =================================
> > Help make your TechAssist database better!
> > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
> > =================================
> > To UNSUBSCRIBE your email address, click here:
> > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> >
> >
> 
> =================================
> Help make your TechAssist database better!  
> Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
> =================================
> To UNSUBSCRIBE your email address, click here:
> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> 
> 


=================================
Help make your TechAssist database better!  
Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
=================================
To UNSUBSCRIBE your email address, click here:
mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe

Other related posts: