I met a fellw once who desoldered with freeze spray. He didn't care that he wound up with blobs of solder all over the board. As for me, I swear by solder-wik. I buy it in 50 ft rolls, but splurged last time for a 100ft roll. John Myers Myers TV Service Co. 376 E. State St. Alliance, OH 44601 Voice / Fax: 330-821-6545 Myers_tv_b@xxxxxxxxxxxxx http://www.myerstv.net Work as if you were to live a hundred years, Pray as if you were to die tomorrow. Ben Franklin tjanphyl@xxxxxxxxxxxxxxx wrote: > I have several of those blue spring loaded desolder tubes you cock on > your knee and push the button. It sucks flyback pins good,and any > massive globs and I use wik on the ICs. You know this is like > anything. Bowling, skeets,baseball,fishing.You can find a dozen guys > who swear BY one thing, and the other dozen swears AT it. Do what you > are most efficient with and that's what will make you more money. > Phil > > Phil Bader, Pres. > Jan Phyl TV Inc > Winter Haven, Fl > (863) 299-8821 > estab. 1976 > > ----- Original Message ----- > From: Electric Medic <info@xxxxxxxxxxxxxxxxx> > Date: Sunday, July 24, 2005 12:31 pm > Subject: [TechAssist] Re: 1 pound roll solder, 50 feet of chem wick > > >>Wayne: I tried those desolder stations one time, it was a Pace. It >>was blue >>with a foot pedal and all. Had a long clear hose that ran up to >>the tool. I >>was not coordinated enough to use it. I tried and tried to work that >>contraption, I was running solder all over the board. I couldn't >>suck and >>heat at the same time. I would suck after the solder was cool or >>vice versa. >>I would melt the plastic tip so the hole was to big then it would >>slurp up >>chip components. I wouldn't even try it on those tiny areas where >>those chip >>components are everywhere. I remember using it on a tuner that I >>replaced on >>some brand and I sucked up a chip resistor and I almost never >>figured out >>what was wrong with that set. Plus, I couldn't use it on service >>calls. I >>know I waste a lot of wick especially on flybacks, I must have 6" >>of the >>stuff hanging with solder on it taking out a flyback, but I am >>used to it. >> >>Perry Bower >>Electric Medic >>"It's Cheaper to Keep Her" >>http://www.electricmedic.com >>3850 Washington Road Suite 4C >>Martinez, Georgia 30907 >>Phone: 706-8MEDIC4 (863-3424) >>Phone: 706-863-3474 >>Fax: 706-863-2316 >>mailto:info@xxxxxxxxxxxxxxxxx >> >> >>-----Original Message----- >>From: techassist-bounce@xxxxxxxxxxxxx >>[mailto:techassist-bounce@xxxxxxxxxxxxx]On Behalf Of Wayne Vanaman >>Sent: Sunday, July 24, 2005 10:49 AM >>To: techassist@xxxxxxxxxxxxx >>Subject: [TechAssist] Re: 1 pound roll solder, 50 feet of chem wick >> >> >>Hey Perry, buy a desolder station. >>I put the date on a 50 foot roll of chem wick when I opened it: 26 >>june2001. I finished that roll off on 26 June 2005. Four years. >> >>Not only will you spend less on chem wik, desoldering is faster >>with a >>desolder station. I spend about a dollar a month on filters. Much >>cheaper than chem wik. It takes about two seconds to desolder a >>joint,and no damage to the board. >> >>If I used two rolls of solder wik a month, 2x$10=$20 $20x48 months= >>$960. I bought my solder station for about $1500 in 1993. That > > would > >>be 144 months times $20 = $2880 minus the $1500= over $1300 savings, >>plus the time saved. My solder station was paid for long, long ago. >> >>Wayne Vanaman >>Omega Electronics >>6904 W Fairfield Dr >>Pensacola, Fl. 32506-3310 >> >>Wayne@xxxxxxxxxxxxxxxxxxxxx >>WWW.PensacolaTVRepair.Com >> >>850-456-5995 voice >>850-458-6369 fax >> >> >>Electric Medic wrote: >> >>>Is that correct? 18 Month's for one roll of solder? I never >> >>thought about >>it >> >>>and I am not sure how long it takes me to go through a roll. I >> >>use off >>rolls >> >>>everywhere, one in my toolbox, one in the truck, and one on each >> >>bench. I >> >>>know my wife bought about 20 rolls of the stuff sitting up there >> >>on the >> >>>shelf. I think the parts salesperson talks us into a roll every >> >>time we >> >>>order parts. That will probably last me 30 years. Hey, I finally > > was > >>>good-newsed, I won't have to by solder again. I can retire on >> >>what I have. >>I >> >>>wish the wick would last that long. I must go through those 50' >> >>foot white >> >>>round ones in 2 weeks. >>> >>>Perry Bower >>>Electric Medic >>>"It's Cheaper to Keep Her" >>>http://www.electricmedic.com >>>3850 Washington Road Suite 4C >>>Martinez, Georgia 30907 >>>Phone: 706-8MEDIC4 (863-3424) >>>Phone: 706-863-3474 >>>Fax: 706-863-2316 >>>mailto:info@xxxxxxxxxxxxxxxxx >>> >>> >>> >> >>------------------------------------------------------------------- >>--------- >>- >>This Email List is Public. Remove: http://www.tech- >>assist.org/remove.htmSet Vacation >>mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation >>Lost Password: http://www.tech-assist.org and select "Login >>Problems?".Email Archives: >>//www.freelists.org/archives/techassist/ >>------------------------------------------------------------------- >>---------- >>This Email List is Public. Remove: http://www.tech- >>assist.org/remove.htmSet Vacation >>mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacationLost > > Password: http://www.tech-assist.org and select "Login Problems?". > >>Email Archives: //www.freelists.org/archives/techassist/ >> > > ----------------------------------------------------------------------------- > This Email List is Public. Remove: http://www.tech-assist.org/remove.htm > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- This Email List is Public. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/