[SI-LIST] Re: capacitor impedance in time domain

arpad,
i didn't quite understand some of the characters in your equation. 
when you write (finite dV)/(dI = 3D 0) = 3D> infinite impedance, 
what do you mean?

yes, in my case the input waveform to the tline is a trapezoidal 
signal 0V to 1V. the setup is shown below. 

signal source -- 50 ohm resistor -- transmission line-- capacitor to 
ground.

when i monitor the voltage at the junction of the resistor and the 
tline, i see it jumps to 0.5V initially which makes sense. However, 
when the reflection from the end comes back, it dips down very fast 
and then rises in an exponential fashion. The dip down looks 
parabolic (2nd order). The dip does go to zero for a zero rise time 
input, but it does not go to zero for a finite rise time signal. i 
am trying to figure out the best way to calculate the amount of this 
dip...

thanks for you help.





--- In si-list@xxxxxxxxxxxxxxx, "Muranyi, Arpad" 
<arpad.muranyi@xxxx> wrote:
> You will get full reflection, because the impedance
> you need to use for the equation you quoted is the
> small signal (AC) impedance.  Referring to my previous
> posting a short time ago, the constant current source
> equivalent during the ramping portion of your trapezoid
> waveform has a (finite dV) / (dI =3D 0) =3D> infinite impedance.
> 
> The question I have for you is this:  where do you mean
> that your waveform is trapezoid?  At the beginning of
> the T-line, or at the end, where the capacitor is?
> If the first, be prepared for a non trapezoid waveform
> at the capacitor, because the T-line and the cap forms
> an RC circuit, who's response is an exponential waveform.
> If the ramp is faster the RC constant you will see
> an exponential waveform, if it is slower, you will see
> a more or less trapezoid waveform.
> 
> I hope this helps,
> 
> Arpad
> 
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=
> 
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=
> =3D=3D=3D=3D=3D
> 
> 
> -----Original Message-----
> From: si-list-bounce@xxxx [mailto:si-list-bounce@xxxx] =
> On Behalf Of group_delay
> Sent: Friday, January 28, 2005 1:48 PM
> To: si-list@xxxx
> Subject: [SI-LIST] Re: capacitor impedance in time domain
> 
> 
> hi all,
> what i really want to do is find out how much waveform gets 
reflected
> from the end of a lossless transmission line terminated with a
> lossless capacitor, assuming the input waveform is a trapezoidal
> signal. I know this can be computed using: gamma =3D (Zl-Zo)/
(Zl+Zo),
> but this requires you to calculate Zl for the time domain signal. 
If I
> wanted to avoid it and use time domain analysis, how would I setup 
the
> equation?
> 
> thanks,
> chris
> 
> 
> --- In si-list@xxxxxxxxxxxxxxx, steve weir <weirsp@xxxx> wrote:
> > matthias, in the time domain we would solve the differential
> equations for=20
> > the network, or more likely using a computer program we would 
solve =
> the=20
> > difference equations over a series of discrete time steps.  Now 
in
> either=20
> > case we could express impedance as dv/dt / di/dt.  But I don't 
know =
> how=20
> > useful it would be towards either visualizing behavior, or 
solving the =
> 
> > equations.  Let's take the trapezoidal wave for instance.  An =
> effective=20
> > impedance is pretty easy to come by on each:  the rising, and 
falling=20
> > portions of the waveform from the capacitance expression C =3D
> i/dv/dt, Z =3D=20
> > dv/dt / di/dt =3D 1/(dv/dt * C ).  The flat portions are 
troublesome
> as are=20
> > the vertices, since dv/dt theoretically goes to zero and the
> impedance from=20
> > the formula jumps to an infinite value.  Intuition should tell us
> that this=20
> > is wrong, as
> 
>  coupling capacitors routinely pass high frequency pulses.
> >=20
> > In the frequency domain, we have this nailed.  We don't have=20
> > discontinuities at the vertices.  The vertices and flat portions 
=
> follow=20
> > curves formed by the frequency components, and rather than a flat
> section=20
> > containing DC and no HF, quite the opposite is true:  the 
flatter we
> want=20
> > the pulse tops to be, the higher the frequency content 
required.  This =
> 
> > aligns with our intuition.  But when we transform the 
representation
> back=20
> > to the time domain, those piecewise linear segments are now 
curved
> solving=20
> > the discontinuities at the vertices and eliminating the flat 
slopes
> with=20
> > theoretically infinite Z between the edges.
> >=20
> > So if someone wanted to look only at the rising and falling 
edges, an=20
> > impedance in the time domain is reasonable, and possibly even
> useful.  But=20
> > it really gets awkward when dealing with the whole waveform 
unless
> we first=20
> > perform frequency limiting operations, most easily performed in 
the=20
> > frequency domain.
> >=20
> > I am not an expert on algorithms, so I really can't say from an 
error=20
> > analysis and computational efficiency standpoint what is really 
the
> best=20
> > way to perform a transient analysis.  But in my naivete, I would 
be=20
> > inclined to transform everything into the frequency domain, 
compute =
> the=20
> > solution and transform back.  In my feeble mind, this would avoid
> some of=20
> > the discontinuity and convergence problems in SPICE and more 
closely=20
> > follows nature.  But since people a whole lot better at math 
than I
> have=20
> > worked long and hard on those algorithms, I suspect either the=20
> > computational overhead, or error build-up of my naive approach 
would =
> be=20
> > unacceptably high.  Maybe what this world needs is a five cent, 
256 =
> bit=20
> > floating point, matrix solver!
> >=20
> > Steve.
> >=20
> > At 10:13 PM 1/26/2005 +0100, Matthias Bergmann wrote:
> > >
> > >Hello, I don`t understand why impedance should be limited to =
> Frequency
> > >domain. What impedance are we speaking about ? For example the
> > >characteristicimpedance Z of a transmission line also exists in
> time domain.
> > >If you look along a transmission line, v(t) / i(t) have got
> singularities
> > >(undefined, infinite), these are called short and open ?!?!?
> Furthermore
> > >mostof the simulation programs use the time domain because it 
permits
> > >non-linearities. I don`t know how what happens when your 
impulse is
> > >trapezoidal, but if it was a rectangular and your load is a
> capacitance, you
> > >are answer would look like an exponential function, with your
> reflection
> > >co-efficient as initial value. Regards, Matthias Bergmann P.S.:
> Yes, use
> > >SPICE or ADS ! _m |---------+---------------------------------->
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >-
list@xxxx>&#160;&#160;&#160;&#160;&#160;&#160;&#160&#160;&#160;&#160
> > >-LIST] Re: capacitor impedance in time
> >
> 
>domain&#160;&#160;&#160;&#160;&#160;&#16&#160;&#160;&#160;&#160;&#16
0;&#=
> 160;&#1
> >
> 
>60I&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160
;&#1=
> 60;&#16
> > >&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;|
> >
> >&#160;>-----------------------------------------------------------
------=
> ----
> > >-- &#160;-----------------------------------------| >I could be
> wrong >but
> > >tome >impedance is a concept strongly related to Frequency 
domain.
> >>It is
> > >meaningful just in that domain. Absolutely. If you define 
impedance =
> as
> > >voltage/current, then you run into great difficulties if you 
try to
> do it in
> > >the time domain.&#160; In general, with any complex impedance,
> v(t)/i(t) has
> > >singularities (undefined, infinite). I consider impedance =3D
> v(s)/i(s) or
> > >v(f)/i(f), which makes it a strictly frequency domain parameter.
> Regards,
> > >Andy
> ------------------------------------------------------------------ 
To
> > >unsubscribe from si-list: si-list-request@xxxx 
with 'unsubscribe'
> > >inthe Subject field or to administer your membership from a web
> page, go to:
> > >http://www.freelists.org/webpage/si-list For help:
> > >si-list-request@xxxx with 'help' in the Subject field List FAQ 
wiki
> > >page is located at:
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160&#160;&#1
60;&=
> #160;
> > >&#160;&#160;http://si-list.org/wiki/wiki.pl?Si-List_FAQ List =
> technical
> > >documents are available at:
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#1&#160;&#160;&#160
;&#1=
> 60;&#16
> > >&#160;http://www.si-list.org List archives are viewable at:
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#
160;=
> &#160;
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;ht
tp:/=
> /www.
> > >freelists.org/archives/si-list or at our remote archives:
> >
> 
>&#160;&#160;&#160;&#1&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160
;&#1=
> 60;&#16
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;http://g
roup=
> s.yah
> > >oo.com/group/si-list/messages Old (prior to June 6, 2001) list
> archives are
> > >viewable at:
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#
160;=
> &#160;
> >
> 
>&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;&#160;ht
tp:/=
> /www.
> > >qsl.net/wb6tpu
> > >----------------------------------------------------------------
--
> > >To unsubscribe from si-list:
> > >si-list-request@xxxx with 'unsubscribe' in the Subject field
> > >
> > >or to administer your membership from a web page, go to:
> > >http://www.freelists.org/webpage/si-list
> > >
> > >For help:
> > >si-list-request@xxxx with 'help' in the Subject field
> > >
> > >List FAQ wiki page is located at:
> > >                 http://si-list.org/wiki/wiki.pl?Si-List_FAQ
> > >
> > >List technical documents are available at:
> > >                 http://www.si-list.org
> > >
> > >List archives are viewable at:
> > >                 http://www.freelists.org/archives/si-list
> > >or at our remote archives:
> > >                 http://groups.yahoo.com/group/si-list/messages
> > >Old (prior to June 6, 2001) list archives are viewable at:
> > >                 http://www.qsl.net/wb6tpu
> > >
> >=20
> >=20
> > -----------------------------------------------------------------
-
> > To unsubscribe from si-list:
> > si-list-request@xxxx with 'unsubscribe' in the Subject field
> >=20
> > or to administer your membership from a web page, go to:
> > http://www.freelists.org/webpage/si-list
> >=20
> > For help:
> > si-list-request@xxxx with 'help' in the Subject field
> >=20
> > List FAQ wiki page is located at:
> >                 http://si-list.org/wiki/wiki.pl?Si-List_FAQ
> >=20
> > List technical documents are available at:
> >                 http://www.si-list.org
> >=20
> > List archives are viewable at:    =20
> >             http://www.freelists.org/archives/si-list
> > or at our remote archives:
> >             http://groups.yahoo.com/group/si-list/messages
> > Old (prior to June 6, 2001) list archives are viewable at:
> >             http://www.qsl.net/wb6tpu
> 
> 
> 
> ------------------------------------------------------------------
> To unsubscribe from si-list:
> si-list-request@xxxx with 'unsubscribe' in the Subject field
> 
> or to administer your membership from a web page, go to:
> http://www.freelists.org/webpage/si-list
> 
> For help:
> si-list-request@xxxx with 'help' in the Subject field
> 
> List FAQ wiki page is located at:
>                 http://si-list.org/wiki/wiki.pl?Si-List_FAQ
> 
> List technical documents are available at:
>                 http://www.si-list.org
> 
> List archives are viewable at:    =20
>               http://www.freelists.org/archives/si-list
> or at our remote archives:
>               http://groups.yahoo.com/group/si-list/messages
> Old (prior to June 6, 2001) list archives are viewable at:
>               http://www.qsl.net/wb6tpu
>  =20
> 
> ------------------------------------------------------------------
> To unsubscribe from si-list:
> si-list-request@xxxx with 'unsubscribe' in the Subject field
> 
> or to administer your membership from a web page, go to:
> http://www.freelists.org/webpage/si-list
> 
> For help:
> si-list-request@xxxx with 'help' in the Subject field
> 
> List FAQ wiki page is located at:
>                 http://si-list.org/wiki/wiki.pl?Si-List_FAQ
> 
> List technical documents are available at:
>                 http://www.si-list.org
> 
> List archives are viewable at:     
>               http://www.freelists.org/archives/si-list
> or at our remote archives:
>               http://groups.yahoo.com/group/si-list/messages
> Old (prior to June 6, 2001) list archives are viewable at:
>               http://www.qsl.net/wb6tpu



------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field

or to administer your membership from a web page, go to:
http://www.freelists.org/webpage/si-list

For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field

List FAQ wiki page is located at:
                http://si-list.org/wiki/wiki.pl?Si-List_FAQ

List technical documents are available at:
                http://www.si-list.org

List archives are viewable at:     
                http://www.freelists.org/archives/si-list
or at our remote archives:
                http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
                http://www.qsl.net/wb6tpu

Other related posts: