On Wed, 2003-11-19 at 20:13, Samuele Rimella wrote: > Ok ho fatto un paio di controlli con lspci e mii-diag ed eccovi i risultati: > > > > report for eth1 > 00:05.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev > 78) > Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management > NIC > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (2500ns min, 2500ns max), cache line size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at 6400 [size=128] > Region 1: Memory at e4000000 (32-bit, non-prefetchable) [size=128] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > > eth0 > 00:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10) > Subsystem: OVISLINK Corp. LFE-8139ATX > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (8000ns min, 16000ns max) > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at 6800 [size=256] > Region 1: Memory at e4001000 (32-bit, non-prefetchable) [size=256] > Expansion ROM at <unassigned> [disabled] [size=64K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1+,D2+,D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > Report for eth0 > mii-diag.c:v2.02 5/21/2001 Donald Becker (becker@xxxxxxxxx) > http://www.scyld.com/diag/index.html > Basic registers of MII PHY #32: 0000 0000 0000 0000 0000 0000 0000 0000. > Basic mode control register 0x0000: Auto-negotiation disabled, with > Speed fixed at 10 mbps, half-duplex. > Basic mode status register 0x0000 ... 0000. > Link status: not established. > Link partner information information is not exchanged when in fixed speed > mode. > End of basic transceiver informaion. > > > report for eth1 > mii-diag.c:v2.02 5/21/2001 Donald Becker (becker@xxxxxxxxx) > http://www.scyld.com/diag/index.html > Basic registers of MII PHY #24: 3000 782d 0041 6800 05e1 41e1 0007 2801. > The autonegotiated capability is 01e0. > The autonegotiated media type is 100baseTx-FD. > Basic mode control register 0x3000: Auto-negotiation enabled. > You have link beat, and everything is working OK. > Your link partner advertised 41e1: 100baseTx-FD 100baseTx 10baseT-FD 10baseT. > End of basic transceiver informaion. > > > > cosa ne pensate? penso che eth0 non vada cosa devo pensare ancora? dammi un aiutino :) Ciao -- Dirie TeNz