Selon C.Breukel@xxxxxxx: No, it is not a spray, it is a tape. > Hi Georges, > > Thanks for the suggestion, not sure if I want to spray adhesive in my > holders though. > > Best, > > Cor > > > -----Original Message----- > > From: pure-silver-bounce@xxxxxxxxxxxxx [mailto:pure-silver- > > bounce@xxxxxxxxxxxxx] On Behalf Of Georges Giralt > > Sent: woensdag 4 april 2007 11:03 > > To: pure-silver@xxxxxxxxxxxxx > > Subject: [pure-silver] Re: (sligthly OT) Film flatness in a 4*% holder > >=20 > > Hi ! > > there is a 3M double face adhesive of quite small strengh suitable for > > your use. > > I do not remember the exact reference, but is was used in the Jobo > 30x40 > > cm > > borderless easel (it seems it is nt made anymore, if you need the > exact > > reference of the spare part I can provide it for you) > > You can put a stripe of this adhesive on the holder, and stick the > plan > > film to > > it when loading. It is thin enough I think not to cause problems. > > Hope this helps. > > Selon C.Breukel@xxxxxxx: > >=20 > > > Hi, > > > > > > I am starting to test a new prototype of an IR film from MACO (it's > made > > > in the old AGFA Geveart plant in Belgiuu it seems, instead at EFKE > in > > > Croatia). I am supposed to report results first to MACO. > > > > > > Thusfar I have only tested 1 sheet (I got only 10 sheets) and this > film > > > is on an very thin layer (a bit similair to lith film), and has also > > > very heavy curl.=3D20 > > > > > > So the film is anywere from lying flat in the holder. (These facts > are > > > know by MACO and will be corrected once they decide to put this film > in > > > production). > > > > > > Obviously I am worried about sharpness, I seem to recall that there > is > > > not much room for depth of focus (at the film surface) as there is > room > > > at the depth of field end. > > > > > > Is that correct, ie when stopping down I can not compensate for the > lack > > > of film flatness in the holder? > > > > > > Will my final print be sharp in the middle, but get blurry towards > the > > > edges? > > > > > > The one sheet I developed and printed did seemed less sharp > compaired to > > > the Rollei Infrared sheet I exposed at the same time. But the > prototype > > > film was a bit overexposed and under developed. > > > > > > Mybe I should slide an old 4*5 flat sheet undeneath the thin film? > > > > > > Best, > > > > > > Thanks, > > > > > > Cor > > > > > > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D > =3D=3D > > = > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D > > > To unsubscribe from this list, go to www.freelists.org and logon to > your > > > account (the same e-mail address and password you set-up when you > > > subscribed,) and unsubscribe from there. > > > > >=20 > >=20 > > -- > > > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D > =3D=3D > > = > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= > =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D > > To unsubscribe from this list, go to www.freelists.org and logon to > your > > account (the same e-mail address and password you set-up when you > > subscribed,) and unsubscribe from there. > ============================================================================================================= > To unsubscribe from this list, go to www.freelists.org and logon to your > account (the same e-mail address and password you set-up when you > subscribed,) and unsubscribe from there. > -- ============================================================================================================= To unsubscribe from this list, go to www.freelists.org and logon to your account (the same e-mail address and password you set-up when you subscribed,) and unsubscribe from there.