[pskmail] Re: SV: Re: SV: Re: SV: Re: SV: Re: SV: Re: SV: Re: Ping

No problem.
Glad to have helped a bit.
I have gated 8 different call-signs today so far.
Roger
On 06/03/2011 15:51, Gunnar Bulukin wrote:

Roger,
I will leave it like this for a week.
Interesting is 2 beacon 1101! I just followed the setup I got from Rain. I
was wondering a bit on why the server was beaconing twice but don't
understand why. I must have made a mistake in pskmailrc.pl!!
 From next Sunday I will change to 40m as suggested by Per, just need some
more lessons from Per;-)
73 de Gunnar

-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx [mailto:pskmail-bounce@xxxxxxxxxxxxx] För
G6CKR
Skickat: den 6 mars 2011 16:36
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: SV: Re: SV: Re: SV: Re: SV: Re: SV: Re: Ping

Just been in shack for a while either side of 15:00 local and the tx
frequency looks OK now.
I was only talking about the last 10 Hz or less for the Fldigi sound card TX
off set.
I guess the idea was to fill in the last bit below the smallest VFO step
which could be done with XIT etc.
Again it's is fine for testing as it is. If long term you are changing
things including radio leave the radio side as is and enjoy.
Re Beacons I did see some almost clashes and you seem to have 2 beacons in
each minute.
There has been clashes with Client beacons when a few have been on so maybe
the client needs a second 5 minute block for 30 minute beacons.
73 Roger

On 06/03/2011 14:53, Pär Crusefalk wrote:

Hi,

Be careful if you move using fldigi as that 500 Hz filter could cut
the high or the low end of the audio. I'd move using the VFO for now.

Regarding the TX'ing you have a point that too many beacons will at
some point hurt us. During the last conference we all agreed that a
server should not beacon more than once per hour and frequency so I
suggest you keep it simple and only beacon once (until you start
covering more frequencies that is).

More servers are always needed! There are of course many servers on
10147 now and perhaps we can use your server to cover more areas?
If I can wish out loud then it would be great if you could cover 40
meters. For instance we have Torsten, SA2ATJ, up in Luleå that will
sail soon and our coverage up there is not perfect now. 40 Meters
would help him and others up there. 40 from your QTH should be good in
middle europe during mornings and evenings too.

A proper installation is very good, that way you can set it up with
cron jobs that fetch files for the users, web server access etc. Lots
to learn still ;-)

73 de Per
SM0RWO


2011-03-06 15:23, Gunnar Bulukin skrev:

OK Roger got that and will check settings again. From what I
understand it seems to connect ok now.
One thing that I have to talk to Rain/Pär/? about is if I make my
server permanent if 1101 on the hr, 20 and 40 is ok to TX on without
to interfere with the other servers. Also if it is needed to have an
server at my QTH? No idea to fill the world with servers!!!
If ok I have to get a new rig for this because the IC-706MKIIG I will
install in my sailing boat and the 2 IC-707, from what I understand,
are difficult to get to work with this apl. (a bit to old!) I also
need to make a new installation of Ubuntu on my fanless computer to
make things more permanent, CD and stick is ok but not optimal.
Going from 0 to 30% learning has taken some time going from 31 to
100% will take quite some time more and there are more things around
the house that has to be taken care of;-)
73 de Gunnar

-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx
[mailto:pskmail-bounce@xxxxxxxxxxxxx] För G6CKR
Skickat: den 6 mars 2011 14:55
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: SV: Re: SV: Re: SV: Re: SV: Re: Ping

    You don't need Cat control for the sound card tweak it just moves
the actual audio tone tx frequency up or down by the set adjustment.
Your TX frequency is made up of the dial frequency plus the waterfall
setting say 1KHz.
If your actual TX frequency turns out to be say 10 Hz too high,
setting -10 in Fldigi sound card TX offset will make the tone centre
990 Hz and correct the difference.
It is there for situations where the RX frequency is fine but the TX
needs minor adjustment.
73 Roger G6CKR


On 06/03/2011 13:43, Gunnar Bulukin wrote:

I am not using CATcontrol so I am changing on the rig. I will go
back to .01 from .00 1315Z
73 Gunnar



-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx
[mailto:pskmail-bounce@xxxxxxxxxxxxx] För G6CKR
Skickat: den 6 mars 2011 12:29
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: SV: Re: SV: Re: SV: Re: Ping

go 10146.1 first a .2 jump will be too far. the .1 might be as well
You can make small changes in fldigi under sound card TX off set 1Hz
at a time add - for lower just the number for higher.
But you are close enough to wait for a few more opinions before you
do anything.
73 Roger


On 06/03/2011 11:19, Gunnar Bulukin wrote:

Ok Roger, I will change down to 10146,0 from 10146,02 please inform
me if there is an improvement.
If you have the time can you send me a mail via my mail gate.
73 de Gunnar

-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx
[mailto:pskmail-bounce@xxxxxxxxxxxxx] För Roger G6CKR
Skickat: den 6 mars 2011 11:29
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: SV: Re: SV: Re: Ping

Done and it works.
First connect failed.
Second was OK.
Server update seemed to go through but I did not get a message back
the first time.
After the "don't know how " message the second update was
acknowledged OK and a mail check worked.
As there was not mail (as expected) I downloaded the Fleet codes.
There were some repeats but not enough to cause a mode change.

Final observation, you TX may be a few Hz HF still, compared to
SM0RWO but it is not far.
73 Roger
G6CKR
On Sun, 2011-03-06 at 08:43 +0100, Gunnar Bulukin wrote:

Hi Roger,

As you are running a client could you test if you can use my
mailgate?

73 de Gunnar

-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx
[mailto:pskmail-bounce@xxxxxxxxxxxxx] För G6CKR
Skickat: den 5 mars 2011 18:14
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: SV: Re: Ping

So if we change the tx setting from 10146.1 to 10146.0 that should
get you to within 20 Hz I think.
if I'm right you will actually be 20 Hz low which you can add to
the Fldigi sound card TX off set.
But do it a step at a time.
look forward to gating you....... Just checked and I have gated
you at
17:02
73 Roger.

On 05/03/2011 17:01, Rein Couperus wrote:

Hej Gunnar,

your server is working, but the TX is 80 Hz too high in frequency...

I got a connect, but 80 Hz difference is really too much....

Pse check with a second receiver, and take IS0GRB-3 as a
reference

frequency...

Tnx,

Rein EA/PA0R/M


Hi Rein,

With some excellent help from Pär I thing that it is working now.
We changed the BFO from 600>      900 and TX from 10146,2>
10146,1

USB.

Now I am getting beacon from G6CKR with no problems.
Maybee now someone can ping me and test if it is working.
Pär told me that there is a program to test the mailfunktion but
it was not on the server cd. Can you tell me how to get it?
73 de gunnar

-----Ursprungligt meddelande-----
Från: pskmail-bounce@xxxxxxxxxxxxx
[mailto:pskmail-bounce@xxxxxxxxxxxxx] För Rein Couperus
Skickat: den 5 mars 2011 11:51
Till: pskmail@xxxxxxxxxxxxx
Ämne: [pskmail] Re: Ping


Hi Gunnar, I have not been able to hear the server yet, but
condx are not good at the moment between us... this what is in
my list this

morning:

09:01 - SM0RWO>PSKAPR,TCPIP*:!5901.16NP01756.10E&
09:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E&
10:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E&
11:02 - IS0GRB-3>PSKAPR,TCPIP*:!3914.79NP00910.96E&

You can see not even SM0RWO makes it into the Igate at the
moment...
IS0GRB-3 is booming in here...

Rein EA/PA0R/M

=====================================================
Hi,

Has anyone been able  to hear or ping SA6BQZ?
TX10146,2 USB  RX10147 CW-N

73 de  gunnar

KB Vågspel
[www.vagspel.se]
Gunnar Bulukin
Tel +46(0)31 962130
Mob +46(0)31 7601501
SMS +46(0)705 933051

This message has been scanned  by Avast for Microsoft Outlook P
Please consider your environmental responsibility. Before
printing this  e-mail ask
yourself:- "Do I need a hard copy?"

Other related posts: