[pskmail] Re: Aw: pskmail server 2.3.5 Defaultmode setting
- From: Pär Crusefalk <per@xxxxxxxxxxxx>
- To: pskmail@xxxxxxxxxxxxx
- Date: Fri, 14 Nov 2014 10:35:48 +0100
Hi,
I've been busy with other stuff a while here but figured I should catch
up, had a look at this.
We used to only have "F", "M" and "" but I see some new stuff there.
Looks like this to me:
F : freqs.txt contains frequencies and fldigi modes so try to set those.
M: freqs.txt contains memory channels and fldigi modes so try to set
those, requires a memtable also.
S: Only get the mode from freqs.txt and send that to fldigi. This code
does not look like the description you had below.
C: This seems odd to me, it sets the command "H" through hamlib (set
memory channel) but manpage says "not implemented yet".
I wouldn't use the last one but I suppose there is a use case for it.
I don't see any "O" anywhere in the code.
I had the PTT issue with my FT897D. Whenever I enable the CAT side of
the interface it will raise RTS and that causes the rig to transmit.
I found no good solution to that, had to get an extra cat interface cable.
73, Per
sm0rwo
Juergen skrev 2014-11-06 17:35:
> I'm sorry, I wrote:
> " If I choose $scanner = "O" or $scanner = "S" "
> this should actually be:
> " If I choose $scanner = "O" or $scanner = "F" "
>
> 73
> Juergen
> DL8JF
>
>> Thanks Rein,
>> I've tried the changes but it only works when I choose $scanner = "S" .
>> If I choose $scanner = "O" or $scanner = "S" then PTT got and stayed
>> triggered every minute . The only possibility to get PTT released then
>> is to push T/R button in fldigi.
>> Is the $Defaultmode in pskmailrc.pl, like described in the PSKmail
>> server 1.0.34 manual, an obsolete entry then ?
>>
>> I found the following description for the $scanner variable:
>> "S" = Single frequency
>> "F" = frequency scanning, config in $HOME/.pskmail/qrg/freqs.txt
>> "M" = memory scan, config in $HOME/.pskmail/qrg/memtable
>> "C" = set memory channel data
>> What does the "O" parameter mean ?
>>
>> 73
>> Juergen
>> DL8JF
>>
>>
>> On 11/05/2014 11:13 PM, Rein Couperus wrote:
>>> Juergen,
>>> the default mode is normally set in the ~/.pskmail/qrg/freqs.txt file.
>>> You can set 5 different modes, which are repeated every 5 minutes.
>>> So when you set all 5 modes to DOMINOEX22 you will be o.k.
>>> In case you don't use frequency scanning, set $scanner = "O";
>>> instead of $scanner = "F"; Fldigi will switch modes then.
>>> The freqs.txt file then looks like e.g:
>>> 10148000,10148000,10148000,10148000,10148000,#22
>>> 10148000,10148000,10148000,10148000,10148000,#23
>>> DOMINOEX22,DOMINOEX22,DOMINOEX22,DOMINOEX22,DOMINOEX22,
>>> Hope this helps,
>>> Rein PA0R
>>> Hi,
>>> I've changed $Defaultmode in pskmailrc.pl from PSK500R to DOMINOEX22
>>> but
>>> after a restart of the pskmail server the Defaultmode is still PSK500R.
>>> If I change it manually to DOMINOEX22 within fldigi, the pskmail server
>>> switch it back to PSK500R after some time.
>>> Any ideas ?
>>>
>>> 73
>>> Juergen
>>> DL8JF
>>>
>>
>>
>
>
Other related posts:
