[modeleng] Re: Shaft pulley retaining

If it's of interest, see the following two links for the data on both:

tds.loctite.com/tds5/docs/601-EN.PDF

tds.loctite.com/tds5/docs/603-EN.PDF

Yours,


Rich.

On Wed, 18 Apr 2012, Clifton wrote:

> Hi Chris,
>
> Having checked in my workshop Locktite 603 is the stuff.
>
> Clif
> ----- Original Message -----
> From: "Chris Crosskey" <chris.crosskey@xxxxxxxxx>
> To: <modeleng@xxxxxxxxxxxxx>
> Sent: Wednesday, April 18, 2012 1:29 PM
> Subject: [modeleng] Re: Shaft pulley retaining
>
>
>> I can easily get 601, 603, 638, 641, 648 and 660.....
>> Chrisc
>>
>>
>>
>>> -----Original Message-----
>>> From: modeleng-bounce@xxxxxxxxxxxxx [mailto:modeleng-
>>> bounce@xxxxxxxxxxxxx] On Behalf Of Clifton
>>> Sent: 18 April 2012 12:06
>>> To: modeleng@xxxxxxxxxxxxx
>>> Subject: [modeleng] Re: Shaft pulley retaining
>>>
>>> Hi Chris
>>>
>>> Locktite 601 I think is the stuff but will double check when I get into
>>> workshop.
>>>
>>> Clean the shaft & pulley with Thinners. Slide the pulley onto shaft
>>> just clear of it position, then run a bit of Loctite onto the shaft,
>>> slide pulley into position & rotate slightly to spread locktite.
>>>
>>> Hold for about 1 min, set in 3 hours, fully hardened in 24 hours. After
>>> which you will need a blowlamp to get it off.
>>>
>>> Will double check the Loctite number later.
>>>
>>> Clif
>>> ----- Original Message -----
>>> From: "Chris Crosskey" <chris.crosskey@xxxxxxxxx>
>>> To: <modeleng@xxxxxxxxxxxxx>
>>> Sent: Wednesday, April 18, 2012 9:11 AM
>>> Subject: [modeleng] Shaft pulley retaining
>>>
>>>
>>>> Does anyone have any recommendation for something that I can retain a
>>>> pulley on a shaft... it's a sliding fit at the moment and I need it
>>> to be
>>>> able to act as a drive for a rotavator.... are any of the loctite
>>>> compounds suitable for this? I'd rather avoid welding it on if at all
>>>> possible.... currently my lathe is out of action during its move from
>>> old
>>>> workshop to the new one otherwise I'd bore out the pulley and weld it
>>> to a
>>>> sleeve that I could shrink fit ontop the shaft... It'd be a bugger to
>>> key
>>>> the shaft BTW, it's close to the cases of the Honda engine it's part
>>> of
>>>> and I don't want to strip the motor ....
>>>> chrisc
>>>>
>>>>
>>> _______________________________________________________________________
>>> _
>>>> This e-mail, and any attachment, is confidential. If you have
>>> received it
>>>> in error, do not use or disclose the information in any way, notify
>>> me
>>>> immediately, and please delete it from your system.
>>>>
>>> _______________________________________________________________________
>>> _
>>>> MODEL ENGINEERING DISCUSSION LIST.
>>>>
>>>> To UNSUBSCRIBE from this list, send a blank email to,
>>>> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
>>> subject
>>>> line.
>>>>
>>>
>>> MODEL ENGINEERING DISCUSSION LIST.
>>>
>>> To UNSUBSCRIBE from this list, send a blank email to,
>>> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
>>> subject line.
>>
>> ________________________________________________________________________
>> This e-mail, and any attachment, is confidential. If you have received it
>> in error, do not use or disclose the information in any way, notify me
>> immediately, and please delete it from your system.
>> ________________________________________________________________________
>> MODEL ENGINEERING DISCUSSION LIST.
>>
>> To UNSUBSCRIBE from this list, send a blank email to,
>> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject
>> line.
>>
>
> MODEL ENGINEERING DISCUSSION LIST.
>
> To UNSUBSCRIBE from this list, send a blank email to,
> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject 
> line.
>
MODEL ENGINEERING DISCUSSION LIST.

To UNSUBSCRIBE from this list, send a blank email to, 
modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.

Other related posts: