RE: Message Screener
- From: "Quillman Shawn (RBNA/CIT1.1) *" <Shawn.Quillman@xxxxxxxxxxxx>
- To: "'[ISAserver.org Discussion List]'" <isalist@xxxxxxxxxxxxx>
- Date: Fri, 4 Apr 2003 10:18:37 -0500
I did it, but I don't have the configuration in front of me.... If I
remember right you have to create packetfilters that block incoming netbios
(TCP/UDP ports 137, 138, 139). Port 139 may be sufficient, it was late when
I did it and I know I've got some overkill in the config. But it works and
nobody's gripin :-)
-Shawn
-----
Shawn R. Quillman
Robert Bosch Corporation RBNA/CIT1.1
38000 Hills Tech Drive
Farmington Hills, MI 48331
(248) 553-1164 (P) (248) 848-2855 (F)
shawn.quillman@xxxxxxxxxxxx
-----Original Message-----
From: Thomas W Shinder [mailto:tshinder@xxxxxxxxxxxxxxxxxx]
Sent: Friday, April 04, 2003 10:10 AM
To: [ISAserver.org Discussion List]
Subject: [isalist] RE: Message Screener
http://www.ISAserver.org
Hi David,
Pretty interesting! I've got to check this out, since just about all my
implementations are stand-alones or stand-alones using IP clustering,
Thanks!
Tom
Thomas W Shinder
www.isaserver.org/shinder <http://www.isaserver.org/shinder>
ISA Server and Beyond: http://tinyurl.com/1jq1 <http://tinyurl.com/1jq1>
Configuring ISA Server: http://tinyurl.com/1llp <http://tinyurl.com/1llp>
-----Original Message-----
From: David V. Dellanno [mailto:ddellanno@xxxxxxxxxx]
Sent: Friday, April 04, 2003 7:34 AM
To: [ISAserver.org Discussion List]
Subject: [isalist] Message Screener
http://www.ISAserver.org
Hi Everyone,
I have setup ISA's message screener sucessfully on a stand-alone ISA Server
2000 but reading the section of artical Q315132 made it very interesting on
how do you complete the ISA's MS installation without performing the
SMTPCred.exe tool? Do they imply if you do have an ISA Array configuration
just skip this section and continue or is this an incomplete document to
support both Stand-alone and Array configurations? Any help would be
appriciated! Thanks everyone,
Dave
HOW TO: Configure SMTP Message Screener in ISA Server 2000 - Q315132
How to Use the SMTPCred.exe Tool to Configure Permissions on the IIS
5.0-Based Server
NOTE: Only use the SMTPCred.exe tool if the ISA Server is installed as a
Stand-Alone ISA Server. If the ISA Server is installed as a member of an
Array, do not use the SMTPCred.exe tool. When ISA Server is installed in an
Array, ISA Server retrieves the settings from Active Directory.
Free Trial Software: Monitor & Manage Web Use with SurfControl Web Filter
for MS ISA Server http://www.surfcontrol.com/go/zisadl1
------------------------------------------------------
List Archives: http://www.webelists.com/cgi/lyris.pl?enter=isalist
ISA Server Newsletter: http://www.isaserver.org/pages/newsletter.asp
ISA Server FAQ: http://www.isaserver.org/pages/larticle.asp?type=FAQ
------------------------------------------------------
Exchange Server Resource Site: http://www.msexchange.org/
Windows Security Resource Site: http://www.windowsecurity.com/
Windows 2000/NT Fax Solutions: http://www.ntfaxfaq.com
------------------------------------------------------
You are currently subscribed to this ISAserver.org Discussion List as:
shawn.quillman@xxxxxxxxxxxx
To unsubscribe send a blank email to $subst('Email.Unsub')
Other related posts:
