[PCB_FORUM] Re: wasn't there a way to "mirror" geometries?

Have you tried assigning the symbols and clines as a "Group" and then
mirroring the group?

I think this might work the only issue is it may also mirror your vias
and if some of them are 

Test points the access pad may be on the wrong side of the board now.

 

Gerry Meier, Sr. PCB Designer

Freedom CAD Services. Inc

Voice: (256)776-7470 or (603) 864-1350

Email:gerry.meier@xxxxxxxxxxxxxx

visit us at http://www.freedomcad.com

 

 

________________________________

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
george.h.patrick@xxxxxxxxxxxxx
Sent: Tuesday, January 15, 2008 11:06 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: wasn't there a way to "mirror" geometries?

 

 

I'm sorry, you are right.  I thought I had done that in 15.2, but
obviously I was wrong as it doesn't work in 15.7 or 16.0.   :}  My
apologies to anyone who was going nutz trying to figure out how it was
done...

 

Been working support too long :[

 

 

-- 
George Patrick
Tektronix, Inc.
Central Engineering, EDS Applications Support
P.O. Box 500, M/S 39-512
Beaverton, OR 97077-0001
* 503-627-5272 (voice)     * 503-627-5587 (fax)
http://www.tektronix.com <http://www.tektronix.com/>
http://www.pcb-designer.com <http://www.pcb-designer.com/> 
 
"Off-Grid and Proud of it!"

        -----Original Message-----
        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Robert
Szumowicz
        Sent: Monday, November 26, 2007 23:51
        To: icu-pcb-forum@xxxxxxxxxxxxx
        Subject: [PCB_FORUM] Re: wasn't there a way to "mirror"
geometries?

        George,
        
        How did you manage to mirror a module? I tried it and the mirror
command does not apply to a single unit which is a module. I could
mirror only components, but not clines/shapes which are also part of the
module. I tried with 15.7 Performance.
        
        Robert
        
        george.h.patrick@xxxxxxxxxxxxx wrote: 

         

        Yep.

         

        -- 
        George Patrick
        Tektronix, Inc.
        Central Engineering, EDS Applications Support
        P.O. Box 500, M/S 39-512
        Beaverton, OR 97077-0001
        * 503-627-5272 (voice)     * 503-627-5587 (fax)
        http://www.tektronix.com <http://www.tektronix.com/>
http://www.pcb-designer.com <http://www.pcb-designer.com/> 
         
        "Off-Grid and Proud of it!"

                -----Original Message-----
                From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
gnieski_mike@xxxxxxx
                Sent: Monday, January 14, 2008 12:26
                To: icu-pcb-forum@xxxxxxxxxxxxx
                Subject: [PCB_FORUM] Re: wasn't there a way to "mirror"
geometries?

                Never tried to mirror a module, works ok?

                 

                 

                
________________________________


                From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
george.h.patrick@xxxxxxxxxxxxx
                Sent: Monday, January 14, 2008 3:14 PM
                To: icu-pcb-forum@xxxxxxxxxxxxx
                Subject: [PCB_FORUM] Re: wasn't there a way to "mirror"
geometries?

                 

                We typically try to do stuff like this as a module.
Especially when we are trying to exactly replicate the circuit.  Then it
can be easily moved/rotated/mirrored without needing to reassign
anything.

                 

                -- 
                George Patrick
                Tektronix, Inc.
                Central Engineering, EDS Applications Support
                P.O. Box 500, M/S 39-512
                Beaverton, OR 97077-0001
                * 503-627-5272 (voice)     * 503-627-5587 (fax)
                http://www.tektronix.com <http://www.tektronix.com/>
http://www.pcb-designer.com <http://www.pcb-designer.com/> 
                 
                "Off-Grid and Proud of it!"

                        -----Original Message-----
                        From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gene Carman
                        Sent: Monday, January 14, 2008 12:09
                        To: icu-pcb-forum@xxxxxxxxxxxxx
                        Subject: [PCB_FORUM] wasn't there a way to
"mirror" geometries?

                        I have to match line and shape of some clines...
is there a way to copy and mirror this lines...  of course I'll also
have the issue of needing to reassign the new nets to them.  Anyone have
any ideas for this?  

                        These are not just matched length, but also
matched curves and shapes of clines.

Other related posts: